background image

Verifying the Kit Contents

2

3

5

4

6

1

NI USRP-2920R

NI USRP-2920R

1. USRP Device
2. AC/DC Power Supply and Power Cable
3. Shielded Ethernet Cable

4. SMA (m)-to-SMA (m) Cable
5. 30 dB SMA Attenuator
6. Getting Started Guide (This Document) and

Safety, Environmental, and Regulatory
Information Document

Notice

 

If you directly connect or cable a signal generator to your device, or if you

connect multiple USRP devices together, you must connect a 30 dB attenuator to the
RF input (RX1 or RX2) of each receiving USRP device.

Other Required Item(s)

In addition to the kit contents, you must provide a computer with available gigabit Ethernet
interface.

Optional Items

LabVIEW Modulation Toolkit (MT), available for download at 

ni.com/downloads

 and

included in LabVIEW Communications System Design Suite, which includes MT VIs
and functions, examples, and documentation

Note

 

You must install the LabVIEW Modulation Toolkit for proper operation

of the NI-USRP Modulation Toolkit example VIs.

LabVIEW Digital Filter Design Toolkit, available for download at 

ni.com/downloads

 and

included in LabVIEW Communications System Design Suite

LabVIEW MathScript RT Module, available for download at 

ni.com/downloads

USRP MIMO sync and data cable, available at

 ni.com

, to synchronize clock sources

USRP-2930/2932 Getting Started Guide

  | 

© National Instruments

  | 

3

Summary of Contents for USRP-2930






















Reviews: