manualshive.com logo in svg

National Instruments SCXI-1129, User Manual

Share
Download
National Instruments SCXI-1129 User Manual Download Page 54

Chapter 2

Using the SCXI-1129

SCXI-1129 User Manual

2-22

ni.com

Figure 2-14.

Cabling a DMM and Using Trig0–Trig7 to Bus the VMC/EXTRIG_1

to a Non-Cabled Module

The SCXI-1129 can accept trigger signals from any of the following
sources:

•

Rear signal connector

•

Front connector

•

Software trigger

•

Triggers 0–7

Note

Not all trigger lines are supported in all chassis. Make sure that the correct chassis

is chosen for your particular application.

Note

Trig0 - Trig7 refers to ttl0 - ttl7 in NI-SWITCH.

Hardware-Timed Scanning Using External
Instruments

When using the SCXI-1129 with an external measurement instrument, you
can use either synchronous or handshaking mode to advance though the
scan list.

Backplane
Connector

HVAB

RSC

Front Connector

Backplane
Connector

Front Connector

SCXI-1129

Backplane
Connector

Front Connector

SCXI-1129

Trig 0

Trig 1

Trig 6

Trig 7

•

•

•

From

DMM AUX

SCANADVD

SCANADVD

SCANADVD

Backplane

SCXI-1129

Summary of Contents for SCXI-1129



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands