background image

USE OF OR THE RESULTS OF THE USE OF THE PRODUCTS IN TERMS OF
CORRECTNESS, ACCURACY, RELIABILITY, OR OTHERWISE. NI DOES NOT
WARRANT THAT THE OPERATION OF THE PRODUCTS WILL BE UNINTERRUPTED
OR ERROR FREE.

In the event that you and NI have a separate signed written agreement with warranty terms
covering the products, then the warranty terms in the separate agreement shall control.

Copyright

Under the copyright laws, this publication may not be reproduced or transmitted in any form,
electronic or mechanical, including photocopying, recording, storing in an information
retrieval system, or translating, in whole or in part, without the prior written consent of
National Instruments Corporation.

National Instruments respects the intellectual property of others, and we ask our users to do the
same. NI software is protected by copyright and other intellectual property laws. Where NI
software may be used to reproduce software or other materials belonging to others, you may
use NI software only to reproduce materials that you may reproduce in accordance with the
terms of any applicable license or other legal restriction.

End-User License Agreements and Third-Party Legal Notices

You can find end-user license agreements (EULAs) and third-party legal notices in the
following locations:

Notices are located in the 

<National Instruments>\_Legal Information

 and

<National Instruments>

 directories.

EULAs are located in the 

<National Instruments>\Shared\MDF\Legal

\license

 directory.

Review 

<National Instruments>\_Legal Information.txt

 for information

on including legal information in installers built with NI products.

U.S. Government Restricted Rights

If you are an agency, department, or other entity of the United States Government
("Government"), the use, duplication, reproduction, release, modification, disclosure or
transfer of the technical data included in this manual is governed by the Restricted Rights
provisions under Federal Acquisition Regulation 52.227-14 for civilian agencies and Defense
Federal Acquisition Regulation Supplement Section 252.227-7014 and 252.227-7015 for
military agencies.

IVI Foundation Copyright Notice

Content from the IVI specifications reproduced with permission from the IVI Foundation.

The IVI Foundation and its member companies make no warranty of any kind with regard to
this material, including, but not limited to, the implied warranties of merchantability and
fitness for a particular purpose. The IVI Foundation and its member companies shall not be

34

  | 

ni.com

  | 

PXIe-6674T User Manual

Summary of Contents for PXIe-6674T





































Reviews: