National Instruments PXI-8187 User Manual Download

Page: 56 / 69

Appendix A

Specifications

NI PXI-8186/8187 User Manual

A-4

ni.com

Electromagnetic Compatibility

Emissions................................................EN 55011 Class A at 10 m

FCC Part 15A above 1 GHz

Immunity ................................................EN 61326:1997 + A2:2001,

Table 1

CE, C-Tick, and FCC Part 15 (Class A) Compliant

Note

For EMC compliance, operate this device with shielded cabling.

CE Compliance

This product meets the essential requirements of applicable European
Directives, as amended for CE marking, as follows:

Low-Voltage Directive (safety)..............73/23/EEC

Electromagnetic Compatibility
Directive (EMC) .....................................89/336/EEC

Note

Refer to the Declaration of Conformity (DoC) for this product for any additional

regulatory compliance information. To obtain the DoC for this product, visit

ni.com/certification

, search by model number or product line, and click the

appropriate link in the Certification column.

Summary of Contents for PXI-8187






































































Search results

Summary of Contents for PXI-8187

Reviews:

Related manuals for PXI-8187

Brands by name

Popular brands

National Instruments PXI-8187, User Manual

Search results

Summary of Contents for PXI-8187

Reviews:

Related manuals for PXI-8187

Brands by name

Popular brands