National Instruments PXI-8110 User Manual Download | Manualshive

Page: 34 / 85

background image

Chapter 2

Installation and Configuration

©

National Instruments Corporation

2-19

NI PXI-8110 User Manual

6.

Expand the PXI controller view in the

Remote Systems

branch and

select

Software

.

7.

Click the

Add/Remove Software

button in the toolbar to launch the

LabVIEW Real-Time Software Wizard.

8.

Install the LabVIEW Real-Time software and device drivers that you
require on the RT target. Refer to the NI Web site at

ni.com/info

and

enter the info code

etspc

for the latest information about supported

software.

After installation of the software the controller will automatically reboot
and you will now be able to program it using LabVIEW Real-Time.

Note

Refer to the

RT Getting Started Guide

available on your host computer for more

information about setting up your RT target.

LabVIEW RT Configuration Switches

Use the LabVIEW RT configuration switches to configure LabVIEW RT
if it is installed on the controller. If you are not using LabVIEW RT, these
switches should remain in the OFF position. The controller reads these
switches only after a system reset.

Note

You must reboot the controller for any changes to take place.

The NI PXI-8110 controller includes the following LabVIEW RT
configuration switches:

•

Switch 1—

Boot LabVIEW RT

: Set this switch to ON to boot

LabVIEW RT.

•

Switch 2—

Boot Safe Mode

: Set this switch to ON to boot

LabVIEW RT into safe mode to reconfigure TCP/IP settings and
to download or update software from a host computer. This switch
overrides the behavior of Switch 1. Booting the controller into safe
mode does not start the embedded LabVIEW RT engine. After
changing the settings or software, reboot the controller with this switch
OFF to resume normal operation.

•

Switch 3—

Disable Startup VI

: Set this switch to ON to prevent VIs

from automatically running at startup if the controller becomes
inaccessible because of a startup VI.

•

Switch 4—

Reset IP Address

: Set this switch to ON to reset the

IP address and other TCP/IP settings to their factory defaults. Use this
switch if moving the controller to a different subnet or if the current
TCP/IP settings are valid.

«
...
32
33
34
35
36
...
»

Summary of Contents for PXI-8110






















































































Reviews:

No comments

Related manuals for PXI-8110

Brand: Ubiquiti Pages: 24

Brand: Samsung Pages: 2

Brand: Samsung Pages: 31

Brand: Samsung Pages: 15

Device Server UDS 10

Brand: Lantronix Pages: 8

Brand: Palo Alto Network Pages: 56

Brand: Paradox Pages: 4

FireWire 800 + Hi-Speed USB Combo

Brand: SIIG Pages: 20

Brand: Telit Wireless Solutions Pages: 113

Brand: Moxa Technologies Pages: 2

Easy Tool-ID BSG TID-05-T30-00-005

Brand: Balluff Pages: 46

memonizerWORKSTATION

Brand: MEMON Pages: 2

TD-3316B4-16P-A1

Brand: TVT Digital Pages: 2

Brand: Altera Pages: 40

Brand: Milesight Pages: 15

Brand: Altimium Pages: 12

Brand: ENERMAX Pages: 33

Brand: Homeworks Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands