National Instruments PCIe-5785 Getting Started Manual Download

Page: 4 / 16

Indoor use only.

Note

For complete specifications, refer to the specifications document for your

device at

ni.com/manuals

Installing the Application Software and Driver

Before installing your hardware, you must install the application software and instrument
driver. Visit

NI FlexRIO Driver Supported Versions for FlexRIO Adapters and Modules

determine which minimum software versions you need for your device. Install the software in
the following order:
1.

Install LabVIEW.

Refer to the

LabVIEW Installation Guide

for installation instructions for LabVIEW and

system requirements for the LabVIEW software. Refer to the

LabVIEW Upgrade Notes

for additional information about upgrading to the most recent version of LabVIEW for
Windows. Documentation for LabVIEW is available at

ni.com/manuals

and by selecting

Start

All Programs

National Instruments

LabVIEW

LabVIEW Manuals

Install the LabVIEW FPGA Module.

Refer to the

LabVIEW FPGA Module Release and Upgrade Notes

for installation

instructions and information about getting started with the LabVIEW FPGA Module.
Documentation for the LabVIEW FPGA Module is available at

ni.com/manuals

and by

selecting

Start

All Programs

National Instruments

LabVIEW

Manuals

(Optional) Install the LabVIEW Real-Time Module.

Refer to the

LabVIEW Real-Time Module Release and Upgrade Notes

for system

requirements, installation instructions, and additional information about using the
LabVIEW Real-Time Module.

Install FlexRIO Support.

Refer to the

FlexRIO Readme

on the FlexRIO installation media for system requirements

and installation instructions for FlexRIO Support. Documentation for FlexRIO Support is
available at

ni.com/manuals

and by selecting

Start

All Programs

National

Instruments

NI FlexRIO

Installing the PCIe-5785

Power off and unplug the computer.

Access the computer system expansion slots. This step might require you to remove one
or more access panels on the computer case.

Locate a compatible slot and remove the corresponding slot cover on the computer back
panel.

Touch any metal part of the computer to discharge any static electricity.

Insert the module into the slot you selected. Gently rock the module in to place without
forcing it.

ni.com

PCIe-5785 Getting Started Guide

Summary of Contents for PCIe-5785

















Search results

Summary of Contents for PCIe-5785

Reviews:

Related manuals for PCIe-5785

Brands by name

Popular brands

National Instruments PCIe-5785, Getting Started Manual

Search results

Summary of Contents for PCIe-5785

Reviews:

Related manuals for PCIe-5785

Brands by name

Popular brands