National Instruments PCI-8361 User Manual Download

Page: 60 / 128

A-18

ni.com

Appendix A

Specifications

Product Certifications and Declarations

Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance
information. To obtain product certifications and the DoC for NI products, visit

ni.com/

product-certifications

, search by model number, and click the appropriate link.

PXI-8360 (191373

-01)

Note

These specifications are typical at 25 °C, unless otherwise stated, and are

subject to change without notice.

Physical

Dimensions

10.0 cm × 16.0 cm (3.9 in. × 6.3 in.)

Maximum cable length

7 m

Slot requirements

One PXI controller slot

Compatibility

Fully compatible with the

PXI Hardware

Specification

, Revision 1.0

Weight

0.25 kg (0.55 lb) typical

Power Requirements

Power Rail

Typical Current

Maximum Current

+3.3 V

1.500 A

1.750 A

+5 V

5 mA

20 mA

+12 V

5 mA

20 mA

-12 V

0 mA

⭥ᆀؑ᚟ӗ૱⊑ḃ᧗ࡦ㇑⨶࣎⌅˄ѝഭ5R+6˅

ѝഭ5R+6

1,ㅖਸѝഭ⭥ᆀؑ᚟ӗ૱ѝ䲀ࡦ֯⭘

—

ḀӋᴹᇣ⢙䍘ᤷԔ5R+6ǄޣҾ1,ѝഭ5R+6ਸ㿴ᙗؑ᚟ˈ䈧ⲫᖅ

ni.com/environment/rohs_china

。

(For information about China

RoHS compliance, go to

ni.com/environment/rohs_china

Summary of Contents for PCI-8361

































































































































Search results

Summary of Contents for PCI-8361

Reviews:

Related manuals for PCI-8361

Brands by name

Popular brands

National Instruments PCI-8361, User Manual

Search results

Summary of Contents for PCI-8361

Reviews:

Related manuals for PCI-8361

Brands by name

Popular brands