National Instruments NI PXIe-8130 User Manual Download | Manualshive

Page: 60 / 84

background image

Chapter 4

Common Configuration Questions

©

National Instruments Corporation

4-3

NI PXIe-8130 User Manual

778713-02 is such a cable and is available through the online catalog at

ni.com/products

.

Figure 4-1.

Y-Splitter Cable

What if I don’t have a Y-splitter cable? Can I still use a mouse and
keyboard?

If you do not have a Y-splitter cable, plug a USB keyboard into any USB
connector. You can also plug a USB mouse into any USB connector.

How do I connect a standard 25-pin LPT cable to the NI PXIe-8130?

The NI PXIe-8130 uses a type C LPT connector. Most parallel port
devices use a type A connector. To use a device with a standard type A
LPT connector, you need to use a type C-to-type A LPT adapter. Parallel
port adapter cables, part number 777169-01, are available through the
online catalog at

ni.com/products

.

Software Driver Installation

How do I install or reinstall the video driver?

Refer to KnowledgeBase 3H3COSD8,

What Peripheral Drivers Should I

Use with My PXI or VXI Controller?

, at

ni.com/support

.

How do I install or reinstall the Ethernet driver?

Refer to KnowledgeBase 3H3COSD8,

What Peripheral Drivers Should I

Use with My PXI or VXI Controller?

, at

ni.com/support

.

«
...
58
59
60
61
62
...
»

Summary of Contents for NI PXIe-8130





















































































Reviews:

No comments

Related manuals for NI PXIe-8130

Brand: ICP DAS USA Pages: 48

Brand: ICP DAS USA Pages: 24

Brand: Lanner Pages: 2

FRDM-STBC-SA9500

Brand: Freescale Semiconductor Pages: 2

Brand: Alesis Pages: 61

CompactPCI CC8-BLUES

Brand: EKF Electronik Pages: 52

Brand: Garland Pages: 43

Brand: OpenVox Pages: 13

Thin Client US310e

Brand: NEC Pages: 6

PBE-5AC-300-ISO

Brand: Ubiquiti Pages: 28

Brand: Cameo Pages: 23

NetVanta Analog Modem Dial Backup Interface Module

Brand: ADTRAN Pages: 2

Brand: Laser Pages: 4

Brand: AMD Pages: 27

Brand: EXAGATE Pages: 7

SRCSASPH16I - RAID Controller

Brand: Intel Pages: 28

Brand: Camozzi Pages: 22

BreezeNET DS.11 Configuration Utility

Brand: Alvarion Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands