manualshive.com logo in svg

National Instruments NI PXI-4220, User Manual

Share
Download
National Instruments NI PXI-4220 User Manual Download Page 33

Chapter 3

Configuring and Testing

NI PXI-4220 User Manual

3-4

ni.com

Shunt Calibration Switches

Shunt calibration switches A and B are software configurable settings that 
allow you to engage or disengage the shunt calibration resistors in order to 
perform gain calibration. In most cases, you do not explicitly control the 
shunt calibration switches, but instead allow driver software to 
automatically adjust them for you during the automated shunt calibration 
procedure. However, if you want to explicitly control the calibration 
switches, you can write an application program that controls the shunt 
calibration switches. Refer to Chapter 4, 

Theory of Operation

, for more 

information.

Note

Null calibration is done for you automatically if you perform shunt calibration using 

the NI-DAQmx driver. Refer to Chapter 4, 

Theory of Operation

, for more information 

about how to perform shunt calibration using the driver.

Simultaneous Sample and Hold

When it is critical to measure two or more signals at the same instant 
in time, simultaneous sample and hold (SS/H) is required. Typical 
applications that might require SS/H include vibration measurements and 
phase difference measurements. You can disable this setting through your 
application if you require scan rates beyond the maximum allowable with 
SS/H engaged. NI recommends leaving SS/H engaged. Disabling SS/H 
introduces a small offset voltage. You can compensate for this offset by 
performing offset null calibration. Refer to Chapter 5, 

Developing Your 

Application

, for more information about how to enable and disable SS/H.

Note

You cannot change the simultaneous sampling mode in MAX. You must use an ADE 

such as LabVIEW to configure the setting. Refer to your ADE help file for more 
information.

Configurable Settings in MAX

Note

If you are not using an NI ADE, using an NI ADE prior to version 7.0, or are using 

an unlicensed copy of an NI ADE, additional dialog boxes from the NI License Manager 
appear allowing you to create a task or global channel in unlicensed mode. These messages 
continue to appear until you install version 7.0 or later of an NI ADE.

You can use MAX to configure your bridge-based sensor measurement. 
This section describes where you can access each software-configurable 
setting available in MAX.

Summary of Contents for NI PXI-4220































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands