manualshive.com logo in svg

National Instruments NI 6520, User Manual, Page: 20 / 23

Share
Download
National Instruments NI 6520 User Manual Download Page 20

NI 6520/6521 User Guide

20

ni.com

Cables and Accessories

NI 6520 Accessory Options

National Instruments offers the following connectivity options for use with 
37-pin safety low voltage (

≤

30 Vrms/42.4 V

pk

/60 VDC) NI 6520 devices.

Screw Terminal Connectivity Options

•

CB-37F Connector Block—part number 778672-01 (vertical) and 
778673-01 (horizontal)

•

CB-37F-LP Unshielded, I/O Connector Block with 37-Pin 
D-SUB—part number 779353-01

•

With one of the following cabling options:

–

SH37F-37M Shielded Cable—part number 778621-01 (1 m) and 
778621-02 (2 m)

–

SH37F-P-4 37-Pin Female-to-Pigtails Shielded I/O Cable—part 
number 778620-04 (4 m)

–

R37F-37M-1 37-Pin Female-to-Male Ribbon I/O Cable—part 
number 779195-01 (1 m)

Or choose from the following custom connectivity options:

•

SH37F-P-4 37-Pin Female-to-Pigtails Shielded I/O Cable—part 
number 778620-04 (4 m)

•

TB-37F-37CP 37-Pin Crimp & Poke Terminals, Shell with Strain 
Relief—part number 779185-01

•

TB-37F-37SC 37-Pin Solder Cup Terminals, Shell with Strain 
Relief—part number 779184-01

For more information about optional equipment available from National 
Instruments, refer to the National Instruments catalog or visit the National 
Instruments Web site at 

ni.com

.

Summary of Contents for NI 6520
























Reviews:

No comments