National Instruments NI 5412 Specifications Download Page 24

Page: 24 / 26

NI 5412 Specifications

ni.com

Physical

Table 16.

Specification

Value

Comments

Dimensions

NI PXI-5412

NI PCI-5412

—

Single 3U PXI slot.

CompactPCI compatible.

2.0

13.0

21.6 cm

(0.8

5.1

8.5 inches)

34.07

10.67

2.03 cm

(13.4

4.20

0.8 inches)

Weight

340 g

(11 oz)

480 g

(17 oz)

—

Front Panel Connectors

Label

Function(s)

Connector Type

—

CH 0

Analog Output

SMB (jack)

CLK IN

Sample clock input and PLL
reference clock input.

SMB (jack)

PFI 0

Marker output, trigger input,
sample clock output,
exported trigger output, and
PLL reference clock output.

SMB (jack)

PFI 1

Marker output, trigger input,
sample clock output,
exported trigger output, and
PLL reference clock output.

SMB (jack)

NI PXI-5412 Only—Front Panel LED Indicators

Label

Function

For more
information, refer
to the

NI Signal

Generators Help.

ACCESS LED

The ACCESS LED indicates the status of the PCI bus and
the interface from the NI 5412 to the controller.

ACTIVE LED

The ACTIVE LED indicates the status of the onboard
generation hardware of the NI 5412.

Included Cable

1 (NI part number 763541-01), 50

Ω

, BNC Male to SMB

Plug, RG223/U, Double Shielded, 1 m cable.

—

Summary of Contents for NI 5412



























Search results

Summary of Contents for NI 5412

Reviews:

Related manuals for NI 5412

Brands by name

Popular brands

National Instruments NI 5412, Specifications

Search results

Summary of Contents for NI 5412

Reviews:

Related manuals for NI 5412

Brands by name

Popular brands