background image

Chapter 1

Getting Started

©

 National Instruments Corporation

1-7

NI PXIe-1075 User Manual

System Controller Slot

The system controller slot is Slot 1 of the chassis and is a 4-Link 
configuration system slot as defined by the CompactPCI Express and 
PXI Express specifications. It has three system controller expansion slots 
for system controller modules that are wider than one slot. These slots 
allow the system controller to expand to the left to prevent the system 
controller from using peripheral slots.

The backplane routes each of the system slots’ x4 PCI Express (PCIe) links 
to a PCIe switch. The four (4) PCIe switches have x4 PCIe links routed to 
each peripheral slot as well as x1 links to two (2) PCIe-to-PCI bridges 
providing 32-bit/33 MHz PCI busses to the hybrid slots. Refer to 
Figure 1-3 for the connectivity of PCIe and PCI.

By default, the system controller will control the power supply with the 
PS_ON# signals. A logic low on this line will turn the power supply on.

Note

The Inhibit Mode switch on the rear of the chassis must be in the 

Default

 position 

for the system controller to have control of the power supply. Refer to the 

Inhibit Mode 

Switch

 section of Chapter 2

Installation and Configuration

for details about the Inhibit 

Mode switch.

Hybrid Peripheral Slots

The chassis provides eight hybrid peripheral slots as defined by the 

PXI-5 

PXI Express Hardware Specification

: slots 2–5 and slots 15–18. A hybrid 

peripheral slot can accept the following peripheral modules:

A PXI Express Peripheral with x4 or x1 PCI Express link to the system 
slot or through a PCIe switch to the system slot.

A CompactPCI Express Type-2 Peripheral with x4 or x1 PCI Express 
link to the system slot or through a PCIe switch to the system slot.

A hybrid-compatible PXI Peripheral module that has been modified by 
replacing the J2 connector with an XJ4 connector installed in the upper 
eight rows of J2. Refer to the 

PXI Express Specification

 for details. The 

PXI Peripheral communicates through the backplane’s 32-bit PCI bus.

A CompactPCI 32-bit peripheral on the backplane’s 32-bit PCI bus.

The hybrid peripheral slots provide full PXI Express functionality and 
32-bit PXI functionality except for PXI Local Bus. The hybrid peripheral 
slot only connects to PXI Local Bus 6 left and right.

Summary of Contents for Network Adapter NI PXIe-1075















































































Reviews: