manualshive.com logo in svg

National Instruments MXI-Express x1 Series, User Manual

Share
Download
National Instruments MXI-Express x1 Series User Manual Download Page 47

B-4

|

ni.com

Appendix B

Specifications

directives with which NI complies, as well as other environmental information not included in 
this document.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers

At the end of the product life cycle, all products 

must

 be sent to 

a WEEE recycling center. For more information about WEEE recycling centers, 
National Instruments WEEE initiatives, and compliance with WEEE Directive 
2002/96/EC on Waste and Electronic Equipment, visit 

ni.com/environment/

weee

.

Cleaning

If you need to clean the module, use a soft, nonmetallic brush. Make sure that the module is 
completely dry and free from contaminants before returning it to service.

NI PCI-8366 (199392

x

-02L)

Note

These specifications are typical at 25 °C, unless otherwise stated, and are 

subject to change without notice.

Note

For instructions to install the low-profile bracket, refer to Appendix D,

NI PCI-8366 Low-Profile Bracket Installation Instructions

. 

Connectivity Support

From Host

Targets

Slot Type

Product

PXI Chassis

NI PXI-8366

NI PXI-8336

*

PCI

NI PCI-8366

—

PCI

NI PCI-8336

*

—

*

*

 The NI PCI-8336 and PXI-8336 are part of the MXI-4 family of products and have the same cable 

connectors as the NI PCI-8366, NI PXI-8366, and NI PXI-8367, but will only function when connected 
in the valid case as shown.

⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩ ˄Ё೑

RoHS

˅

Ё೑ᅶ᠋

National Instruments

ヺড়Ё೑⬉ᄤֵᙃѻકЁ䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽䋼ᣛҸ

 

(RoHS)

DŽ݇Ѣ

National Instruments

Ё೑

RoHS

ড়㾘ᗻֵᙃˈ䇋ⱏᔩ

ni.com/

environment/rohs_china

DŽ

(For information about China RoHS compliance, 

go to 

ni.com/environment/rohs_china

.)

Summary of Contents for MXI-Express x1 Series

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands