manualshive.com logo in svg

National Instruments DAQCard-6715, User Manual

Share
Download
National Instruments DAQCard-6715 User Manual Download Page 18

Chapter 1

DAQ System Overview

©

 National Instruments Corporation

1-3

Analog Output Series User Manual

buffered waveform generation, and buffered period measurement. It also 
supports numerous non-buffered operations, such as single pulse or pulse 
train generation, digital input, and digital output.

Calibration Circuitry

Calibration is the process of making adjustments to a measurement device 
to reduce errors associated with measurements. Without calibration, the 
measurement results of your device will drift over time and temperature. 
Calibration adjusts for these changes to improve measurement accuracy 
and ensure that your product meets its required specifications.

DAQ devices have high precision analog circuits that must be adjusted to 
obtain optimum accuracy in your measurements. Calibration determines 
what adjustments these analog circuits should make to the device 
measurements. During calibration, the value of a known, high precision 
measurement source is compared to the value your device acquires or 
generates. The adjustment values needed to minimize the difference 
between the known and measured values are stored in the EEPROM of the 
device as calibration constants. Before performing a measurement, these 
constants are read out of the EEPROM and are used to adjust the calibration 
hardware on the device. NI-DAQ determines when this is necessary and 
does it automatically. If you are not using NI-DAQ, you must load these 
values yourself.

You can calibrate AO Series devices in the following two ways.

Internal or Self-Calibration

Self-calibration is a process to adjust the device relative to a highly accurate 
and stable internal reference on the device. Self-calibration is similar to 
the autocalibration or autozero found on some instruments. You should 
perform a self-calibration whenever environmental conditions, such as 
ambient temperature, change significantly. To perform self-calibration, use 
the self-calibrate function or VI that is included with your driver software. 
Self-calibration requires no external connections.

External Calibration

External calibration is a process to adjust the device relative to a traceable, 
high precision calibration standard. The accuracy specifications of your 
device change depending on how long it has been since your last external 
calibration. National Instruments recommends that you calibrate your 
device at least as often as the intervals listed in the accuracy specifications.

Summary of Contents for DAQCard-6715








































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands