manualshive.com logo in svg

National Instruments cDAQ-9133, User Manual, Page: 136 / 145

Share
Download
National Instruments cDAQ-9133 User Manual Download Page 136

B-2

|

ni.com

Appendix B

Where to Go from Here

The 

NI cDAQ-9132 Specifications, NI cDAQ-9133 Specifications, NI cDAQ-9134 

Specifications

, 

NI cDAQ-9135 Specifications

, 

NI cDAQ-9136 Specifications

, or 

NI cDAQ-9137 

Specifications 

list all specifications for your cDAQ controller. Go to 

ni.com/manuals

 and 

search for your cDAQ controller.

The 

NI cDAQ Chassis Calibration Procedure

 contains information for calibrating all National 

Instruments CompactDAQ chassis and controllers. Go to 

ni.com/manuals

 and search for 

your cDAQ controller.

C Series Module Documentation and Specifications

For module specifications, refer to the documentation included with your C Series module or go 
to 

ni.com/manuals

.

NI-DAQmx

The 

NI-DAQmx Readme

 lists which devices, ADEs, and NI application software are supported 

by this version of NI-DAQmx. Select 

Start»All Programs»National Instruments» 

NI-DAQmx»NI-DAQ Readme

.

The 

NI-DAQmx Help

 contains API overviews, general information about measurement 

concepts, key NI-DAQmx concepts, and common applications that are applicable to all 
programming environments. Select 

Start»All Programs»National Instruments»Start»

All Programs»National Instruments»NI-DAQmx»NI-DAQmx Help

.

LabVIEW

Refer to 

ni.com/gettingstarted

 for more information about getting started with 

LabVIEW.

Use the 

LabVIEW Help

, available by selecting 

Help»LabVIEW Help

 in LabVIEW, to access 

information about LabVIEW programming concepts, step-by-step instructions for using 
LabVIEW, and reference information about LabVIEW VIs, functions, palettes, menus, and 
tools. Refer to the following locations on the 

Contents

 tab of the 

LabVIEW Help

 for information 

about NI-DAQmx:
•

VI and Function Reference»Measurement I/O VIs and Functions

»

DAQmx - Data 

Acquisition VIs and Functions

—Describes the LabVIEW NI-DAQmx VIs and functions.

•

Property and Method Reference»NI-DAQmx Properties

—Contains the property 

reference.

•

Taking Measurements

—Contains the conceptual and how-to information you need to 

acquire and analyze measurement data in LabVIEW, including common measurements, 
measurement fundamentals, NI-DAQmx key concepts, and device considerations.

Summary of Contents for cDAQ-9133


















































































































































Reviews:

No comments