National Instruments cDAQ-9133 User Manual Download Page 132 | Manualshive

Page: 132 / 145

background image

© National Instruments

|

A-7

NI cDAQ-9132/9133/9134/9135/9136/9137 User Manual

Boot Setup Menu

Use this menu to configure settings related to the boot process and boot device priority.
•

Boot Settings Configuration Submenu

—Use this setting to access the Boot Settings

Configuration submenu.

•

PXE Network Boot

—This setting specifies whether the PXE network boot agent is

enabled. When enabled, the Intel Boot Agent will be displayed in the Boot Option Priorities
menu, allowing you to boot from a PXE server on the local subnet. Note that the Intel Boot
Agent device names are preceded by

IBA GE Slot 0200 v1553

in the Boot Option Priorities

menu. The system must be restarted for this setting to take effect. The default value is

Disabled

.

•

Boot Option Priorities

—These settings specify the order in which the BIOS checks for

bootable devices, including the local hard disk drive, removable devices such as USB flash
disk drives or USB CD-ROM drives, or the PXE network boot agent. The BIOS will first
attempt to boot from the device associated with

1st Boot Device

, followed by

2nd Boot

Device

, and

3rd Boot Device

. If multiple boot devices are not present, the BIOS setup

utility will not display all of these configuration options. To select a boot device, press
<Enter> on the desired configuration option and select a boot device from the resulting
menu. You can also disable certain boot devices by selecting

Disabled

.

Note

Only one device of a given type is shown in this list. If more than one device

of the same type exists, use the appropriate device BBS priorities submenu to re-order
the priority of devices of the same type.

The following submenus are displayed if one or more bootable devices of the corresponding type
is present:
•

Hard Drive BBS Priorities Submenu

—Use this setting to access the Hard Drive BBS

Priorities submenu to re-order or disable bootable hard drive devices.

•

CD/DVD ROM Drive BBS Priorities Submenu

—Use this setting to access the CD/DVD

ROM Drive BBS Priorities submenu to re-order or disable bootable CD/DVD ROM drive
devices.

•

Floppy Drive BBS Priorities Submenu

—Use this setting to access the Floppy Drive BBS

Priorities submenu to re-order or disable bootable floppy drive devices.

•

Network Device BBS Priorities Submenu

—Use this setting to access the Network Device

BBS Priorities submenu to re-order or disable bootable network devices.

«
...
130
131
132
133
134
...
»

Summary of Contents for cDAQ-9133


















































































































































Reviews:

No comments

Related manuals for cDAQ-9133

Brand: Valor Pages: 20

Brand: Rane Pages: 2

Brand: UCS Pages: 4

Brand: Samson Pages: 73

Brand: tams elektronik Pages: 12

FUTERA XLF Series

Brand: RBI Pages: 128

Brand: RBH Access Technologies Pages: 36

Brand: S&C Pages: 11

Brand: S&C Pages: 24

Brand: S&C Pages: 19

Brand: Eaton Pages: 8

Brand: ABB Pages: 44

Brand: Omega Pages: 2

Brand: Zmotion Pages: 34

Brand: hager Pages: 2

Brand: hager Pages: 4

Extinguishing Control Panel BC06-2EXT

Brand: LST Pages: 4

Brand: Rabbit Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands