manualshive.com logo in svg

National Instruments cDAQ-9133, User Manual

Share
Download
National Instruments cDAQ-9133 User Manual Download Page 130

© National Instruments

|

A-5

NI cDAQ-9132/9133/9134/9135/9136/9137 User Manual

Power/Wake Configuration Submenu

Use this submenu to apply alternate configurations to the power and wake features of the chipset 
and controller. Normally, you do not need to modify these settings because the factory default 
settings provide the most compatible and optimal configuration possible.
•

Restore After Power Loss

—This setting specifies the power state that the controller 

should return to after DC power is lost. Valid values are 

Stay Off

 and 

Turn On

. The default 

value is 

Turn On

. When set to 

Stay Off

, the controller returns to the soft off power state 

after AC power is restored. When set to 

Turn On

, the controller powers on when DC power 

is restored.

•

Power Button Off Behavior

—This setting specifies how the system responds to the power 

button. Valid options are 

Normal

 and 

Disabled

. The default value is 

Normal

. If the value 

is 

Normal

, the system responds to the power button as defined by the OS. If the value is 

Disabled

, pressing the power button has no effect when the system is on. When the system 

is in the soft off state, pushing the power button always powers on the system. Refer to the 

Power Button

 section of Chapter 1, 

Getting Started with the cDAQ Controller

, for more 

information.

•

Ring Indicator Wake

—This setting enables or disables the ability to wake a powered-off 

system using the Ring Indicator pin of the RS-232 serial port. The default value is 

Disabled

. Refer to the 

RS-232 Serial Port

 section of Chapter 1, 

Getting Started with the 

cDAQ Controller

, for more information.

•

Wake On Trigger

—This setting enables or disables the ability to wake a powered-off 

system using the PFI 0 connector on the front panel. The default value is 

Disabled

. Refer 

to the 

PFI 0 SMB Connector

 section of Chapter 1, 

Getting Started with the cDAQ 

Controller

, for more information.

SATA Configuration Submenu

Use this submenu to apply alternate settings to the hard disk drive (HDD) interfaces. Normally, 
you do not need to modify these settings because the factory default settings provide the most 
compatible and optimal configuration possible.
•

SATA Controller(s)

—This setting specifies whether the onboard SATA controller is 

enabled or disabled. The default value is 

Enabled

.

•

Onboard Storage

—This item displays the onboard drive detected in the system.

USB Configuration Submenu

Use this submenu to apply alternate configurations to the USB host ports. Normally, you do not 
need to modify these settings because the factory default settings provide the most compatible 
and optimal configuration possible.
•

USB Devices

—This item lists the total number of devices detected in the system, 

categorized by device type.

•

Legacy USB Support

—This setting specifies whether legacy USB support is enabled. 

Legacy USB support refers to the ability to use a USB keyboard and mouse during system 
boot or in a legacy operating system such as DOS. The default value on 

Summary of Contents for cDAQ-9133


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands