manualshive.com logo in svg

National Instruments ATCA-3671, Getting Started Manual, Page: 3 / 26

Share
Download
National Instruments ATCA-3671 Getting Started Manual Download Page 3

Refer to the product readme, which is available online at 

ni.com/manuals

, for more

information about minimum system requirements, recommended system, and supported
application development environments (ADEs).

Unpacking the Kit

Caution

 

To prevent electrostatic discharge (ESD) from damaging the device,

ground yourself using a grounding strap or by holding a grounded object, such as
your computer chassis.

1.

Touch the antistatic package to a metal part of the computer chassis.

2.

Remove the device from the package and inspect the device for loose components or any
other sign of damage.

Caution

 

Never touch the exposed pins of connectors.

Note

 

Do not install a device if it appears damaged in any way.

3.

Unpack any other items and documentation from the kit.

Store the device in the antistatic package when the device is not in use.

Verifying the Kit Contents

•

ATCA-3671 module

•

Ethernet cable

•

ATCA I/O slot blockers (x4)

•

ATCA-3671 Getting Started Guide

 (this document)

Note

 

Your ATCA-3671 kit may contain additional NI ATCA products.

ATCA-3671 Getting Started Guide

  | 

© National Instruments

  | 

3

Summary of Contents for ATCA-3671



























Reviews:

No comments