Nastec SUND Instructions For Installation, Use And Maintenance Manual Download Page 6 | Manualshive

Page: 6 / 40

background image

• irradiation level
• time of day
• achievement of the required daily flow rate
• remote control via digital input.

1.3. Nastec NSC solar calculator

To correctly size the solar pumping system, the Nastec NSC solar calculator is available free of charge on the site

solar.nastec.eu

2. Safety

2.1. Symbols

TIP

This symbol indicates a TIP or recommendation.

NOTE

This symbol indicates a NOTE or an indication or concept to be emphasised.

CAUTION

This symbol indicates CAUTION, thus an indication which failure to respect can lead to minor or
moderate damage.

WARNING

This symbol indicates a WARNING, thus an indication which, in the event of non-compliance, may
lead to serious, even fatal damage to persons or things.

DANGER

This symbol indicates an ELECTRICAL HAZARD, which if not avoided will result in death or electro-
cution.

SUND

6

«
...
4
5
6
7
8
...
»

Summary of Contents for SUND









































Reviews:

No comments

Related manuals for SUND

Brand: Walchem Pages: 31

Delta Solo Compact MVP Series

Brand: KSB Pages: 40

Brand: Baker Hughes Pages: 78

Brand: SPERONI Pages: 68

FIGHTER 2010 Series

Brand: Nibe Pages: 36

Brand: True Source Pages: 27

MegaLife HE Series

Brand: Heatrae Sadia Pages: 24

Brand: Xylem Pages: 21

Brand: Marco Pages: 3

Brand: Trinity Lx Pages: 24

Brand: Trane Pages: 8

Brand: Wacker Neuson Pages: 208

Brand: GORMAN-RUPP PUMPS Pages: 45

Water Quality System EQHP-TWIN 108SP

Brand: Bunn Pages: 2

Brand: Ironton Pages: 17

Brand: Simer Pages: 16

R E U - K M2635FFUDHD-E

Brand: Rinnai Pages: 64

PILE DRIVER 84900

Brand: Lincoln Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands