background image

CAUTION

During operation, some surfaces may reach high temperatures that may cause burns upon contact
with skin. Be very careful when touching the device!
Avoid contact with flammable products.

WARNING

Do not perform insulation tests on the load or power cable without first disconnecting them from the
device.

2.4. Acoustic emission

The device has an acoustic emission:
< 65 dB.

2.5. Certifications

The product has the following certifications:

• CE

3. Maintenance

3.1. Maintenance

WARNING

Before carrying out any work on the device, carefully read the chapter 

Safety [4]

 in the manual.

WARNING

Failure to follow the instructions may result in damage to the product, the system in which it is
installed and, in the worst cases, damage to property or persons with even fatal consequences.

WARNING

Failure to comply with the instructions may lead to loss of warranty.

The device requires the following maintenance:

Intervention

Interval

Check the correct cooling of the unit.

Every 12 months

Check for alarms

Every 12 months

Check the correct tightening of the power terminals

Every 12 months

Verify the maintenance of the protection rating (ingress of dust or water) by checking the tightening of the screws in the
mechanical closing parts, the gaskets, and the cable glands.

Every 12 months

TIP

For more information contact the dealer or technical support at [email protected] or by opening a
support ticket on the portal service.nastec.eu

3.2. Warranty

Nastec guarantees that the products accompanied by this warranty are free from material or workmanship defects.
The Company has the right to inspect any product returned under warranty, and confirm that the product contains
a material or workmanship defect. The Company has the exclusive right to decide whether to repair or replace
defective equipment, parts or components. To qualify for the warranty coverage, the buyer must return the product
to the place of purchase. Subject to the terms and conditions listed below, the Company agrees to repair or
replace any part of this product that has material or workmanship defects. The Company will evaluate products
under warranty for 24 months from the date of installation (only in case of product registration) but no longer than
36 months from the date of invoice. IN NO EVENT shall the Company be liable for any other costs incurred by

PILOT

7

Summary of Contents for PILOT





























Reviews: