English
21
16 Starting the Machine
16.1 Turning the Machine On
The machine is fitted with a safety device to prevent an acci-
dental start [2].
Push the safety [2] in, hold it in place and press the switch [1]. You
can release the safety once the machine is running.
16.2 Turning the Machine Off
Release the switch [1]. The rundown time of the spindle is short‑
ened by a brake once the machine is off.
17 Work Instructions
Fasten the workpiece to a solid base.
Feed that is too high greatly reduces the performance of the tool
and shortens the life of the saw blade and the motor. Use sharp saw
blades suited for the given type of material. A thin oil film on the
saw blade prevents rusting.
Clean the saw blade immediately after work. Glue and resin resi‑
dues reduce the quality of the cut.
17.1 Cutting Plastic
Cutting plastic creates long, spiral shavings. Electrostatic charge
may cause the hole for chip extraction [15] to clog and the mova‑
ble guard [3a] to get stuck.
Workpieces made of plastic must make good contact with the
base/supports underneath. Make careful cuts and work smoothly,
steadily and without interruptions. This prevents the teeth from
getting smeared with plastic and keeps the cut smooth and clean.
18 Maintenance and service
Attention! Risk of el. shock. Prior to start any opera-
tion, pull the plug out of the socket!
18.1 Instructions for Cleaning the
Machine
Blow away dirt and dust from the tool’s vents when the motor is
running. Use protective glasses when doing this. You can clean ex‑
terior plastic parts with a moistened cloth and a mild detergent.
Though these parts are made of materials resistant to solvents,
DO
NOT
use solvents to clean them.
Attention! With respect to protection from el. shock
and preservation of the class of protection, all mainte-
nance and service operations requesting jig saw case
removal must be performed by the authorized service centre
only!
The current list of authorized service centres can be found at our
website
www.narex.cz
, section
“Service Centres”
.
19 Accessories
The accessories recommended for use with this device are availa‑
ble commercially in the shops with hand el. tools.
20 Storage
Packed appliance may be stored in dry, unheated storage place
with temperature not lower than ‑5 °C.
Unpacked appliance should be stored only in dry storage place
with temperature not lower than +5 °C with exclusion of all sudden
temperature changes.
21 Environmental protection
Power tools, accessories and packaging should be sorted for envi‑
ronmental‑friendly recy.
Only for EU countries:
Do not dispose of power tools into household waste!
According to the European Directive 2002/96/EC on waste electri‑
cal and electronic equipment and its incorporation into national
law, power tools that are no longer suitable for must be separate‑
ly collected and sent for recovery in an environmental‑friendly
manner.
22 Warranty
Our equipment is under warranty for at least 12 months with re‑
gard to material or production faults in accordance with national
legislation. In the EU countries, the warranty period for exclusively
private use is 24 months (an invoice or delivery note is required as
proof of purchase).
Damage resulting from, in particular, normal wear and tear, over‑
loading, improper handling, or caused by the user or other dam‑
age caused by not following the operating instructions, or any
fault acknowledged at the time of purchase, is not covered by the
warranty.
Complaints will only be acknowledged if the equipment has not
been dismantled before being sent back to the suppliers or to an
authorised NAREX customer support workshop. Store the operat‑
ing instructions, safety notes, spare parts list and proof of purchase
in a safe place. In addition, the manufacturer’s current warranty
conditions apply.
Note
Due to continuous research and development work, we re‑
serve the right to make changes to the technical content of this
documentation.
23 Certificate of Conformity
EPK 18:
We declare that the device meets requirements of the following
standards and directives.
Safety:
EN 62841‑1:2015
EN 62841‑2‑5:2014
Directive 2006/42/EC
Electromagnetic compatibility:
EN 55014‑1: 2017
EN 55014‑2: 2015
Directive 2014/30/EU
RoHS:
Directive 2011/65/EU
Place of storage of the technical documentation:
Narex s.r.o., Chelčického 1932, 470 01 Česká Lípa, Czech Republic
2022
Narex s.r.o.
Chelčického 1932
Jaroslav Hybner
470 01 Česká Lípa
CEO of the company
May 1, 2022
Summary of Contents for EPK 18
Page 5: ...5 2 10 12a 12b 12c 13a 13a 13b 14a 14b 14c 14d 17 12d 12c...
Page 11: ...esky 11...
Page 33: ...En espa ol 33...
