Napoleon GDS60-N Installation And Operating Instrictions Download Page 4

4

W415-0788 / 05.15.09

 NAPOLEON® warrants its products against manufacturing defects to the original purchaser only. Registering your warranty is not 
necessary. Simply provide your proof of purchase along with the model and serial number to make a warranty claim. NAPOLEON® 
reserves the right to have its representative inspect any product or part thereof prior to honouring any warranty claim. Provided that the 
purchase was made through an authorized NAPOLEON® dealer your heater is subject to the following conditions and limitations:
  This factory warranty is non-transferable and may not be extended whatsoever by any of our representatives.
  The gas heater must be installed by a licensed, authorized service technician or contractor. Installation must be done in accordance 
with the installation instructions included with the product and all local and national building and fi re codes.   This limited warranty does 
not cover damages caused by misuse, lack of maintenance, accident, alterations, abuse or neglect and parts installed from other 
manufacturers will nullify this warranty.
  This limited warranty further does not cover any scratches, dents, corrosion or discoloring caused by excessive heat, abrasive and 
chemical cleaners nor chipping on porcelain enamel parts, mechanical breakage of PHAZER™ logs and embers.
  NAPOLEON® warrants its stainless steel burners against defects in workmanship and material for life, subject to the following 
conditions: During the fi rst 10 years NAPOLEON® will replace or repair the defective parts at our option free of charge. From 10 years 
to life, NAPOLEON® will provide replacement burners at 50% of the current retail price.
  In the fi rst year only, this warranty extends to the repair or replacement of warranted parts which are defective in material or 
workmanship provided that the product has been operated in accordance with the operation instructions and under normal conditions.
  After the fi rst year, with respect to this President’s Lifetime Limited Warranty, NAPOLEON® may, at its discretion, fully discharge all 
obligations with respect to this warranty by refunding to the original warranted purchaser the wholesale price of any warranted but 
defective part(s).
  NAPOLEON® will not be responsible for installation, labour or any other expenses related to the reinstallation of a warranted part and 
such expenses are not covered by this warranty.
  Notwithstanding any provisions contained in the President’s Lifetime Limited Warranty, NAPOLEON’S responsibility under this 
warranty is defi ned as above and it shall not in any event extend to any incidental, consequential or indirect damages.
  This warranty defi nes the obligations and liability of NAPOLEON® with respect to the NAPOLEON® gas heater and any other 
warranties expressed or implied with respect to this product, its components or accessories are excluded.
  NAPOLEON® neither assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the sale of 
this product. 
  NAPOLEON® will not be responsible for: over-fi ring, downdrafts, spillage caused by environmental conditions such as rooftops, 
buildings, nearby trees, hills, mountains, inadequate vents or ventilation, excessive venting confi gurations, insuffi cient makeup air, or 
negative air pressures which may or may not be caused by mechanical systems such as exhaust fans, furnaces, clothes dryers, etc.
  Any damages to heater, combustion chamber, heat exchanger, brass trim or other components due to water, weather damage, long 
periods of dampness, condensation, damaging chemicals or cleaners will not be the responsibility of NAPOLEON®.

2.1

NAPOLEON® products are manufactured under the strict Standard of the world recognized ISO 9001 : 2000 

Quality Assurance Certifi cate.

NAPOLEON® products are designed with superior components and materials assembled by trained 

craftsmen who take great pride in their work. The burner and valve assembly are leak and test-fi red at a 

quality test station. The complete heater is again thoroughly inspected by a qualifi ed technician before 

packaging to ensure that you, the customer, receives the quality product that you expect from NAPOLEON®.

The following materials and workmanship in your new NAPOLEON® gas heater are warranted against 
defects for as long as you own the heater. This covers: combustion chamber, heat exchanger, stainless 
steel burner, phazer™ logs and embers, rocks, ceramic glass (thermal breakage only), gold plated parts 
against tarnishing, porcelainized enameled components and aluminum extrusion trims.*
Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves, thermal switch, 
switches, wiring, remote controls, ignitor, gasketing, and pilot assembly are covered and NAPOLEON® will 
provide replacement parts free of charge during the fi rst year of the limited warranty.*
Labour related to warranty repair is covered free of charge during the fi rst year. Repair work, however, 
requires the prior approval of an authorized company offi cial. Labour costs to the account of NAPOLEON® 
are based on a predetermined rate schedule and any repair work must be done through an authorized 
NAPOLEON® dealer.
* Construction of models vary. Warranty applies only to components included with your specifi c heater.

NAPOLEON® GAS FIREPLACE PRESIDENT’S LIFETIME LIMITED WARRANTY

CONDITIONS AND LIMITATIONS

ALL SPECIFICATIONS AND DESIGNS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE DUE TO ON-GOING PRODUCT 

IMPROVEMENTS.  NAPOLEON® IS A REGISTERED TRADEMARK OF WOLF STEEL LTD.  PATENTS U.S. 5.303.693.801 - CAN. 

2.073.411, 2.082.915. © WOLF STEEL LTD.

1.1 WARRANTY

NorthlineExpress.com

http://www.northlineexpress.com

Toll-Free 1-866-667-8454

Summary of Contents for GDS60-N

















































Reviews: