StarLink
™
SLE
-
MAXVI
-
FIRE & SLE
-
MAXAI
-
FIRE Commercial Series Sole/Dual
-
Path Alarm Communicators
--
Installation Instructions
3
a minimum of 24 hours.
TB19:
N/O OUT1:
Normally open. Dry contact Form C
relay. Add shunt to lower two pins of JP1 for wet
contacts.
TB20:
C OUT1:
Common. Dry contact Form C relay.
Add shunt to lower two pins of JP1 for wet contacts
(connects relay Common to system ground). Relay
rated 30V AC/DC, 500mA.
TB21:
N/C OUT1:
Normally closed. Dry contact Form C
relay. Add shunt to lower two pins of JP1 for wet
contacts.
TB22:
N/O OUT2:
Normally open. Dry contact Form C
relay.
TB23:
C OUT2:
Common. Dry contact Form C relay.
Relay rated 30V AC/DC, 500mA.
TB24:
N/C OUT2:
Normally closed. Dry contact Form C
relay.
LED DESCRIPTIONS
The PC board contains several LEDs, as follows:
GREEN RF SIGNAL STRENGTH LED
Labeled "
D3
", this LED is located at the lower right corner
of the PC board.
Every 30 seconds, the StarLink communicator receiver
section turns on and listens to the cell tower. Depending
on the signal strength detected, it will blink the Signal
Strength LED from 1 to 5 times, providing a signal
strength indicator that is updated constantly and is al-
ways displayed.
Green LED Operation
Signal strength (as received by the communicator) is dis-
played by this LED blinking 1 to 5 times at a constant
rate (with a short delay between blink cycles).
Accepta-
ble power level is greater than or equal to 2 blinks
.
YELLOW OPERATIONAL STATUS LED
Labeled "
D4
", this LED is located at the bottom right of
the PC board. Operation is as follows:
Normal Standby Condition:
•
Blinks on momentarily every 10 seconds:
Unit is in
standby waiting for an alarm to report.
Processing Alarm Conditions:
•
When processing an alarm, this LED will blink variably
during each part of the process (dialing, handshaking,
data transmission, etc.).
RED TROUBLE LED
Labeled "
D5
", this LED is located at the bottom right of
the PC board. Operation is as follows:
•
1 Blink:
Low Aux Power input voltage
•
2 Blinks:
Check Input Power
•
3 Blinks:
Alarm report Failed to Communicate (will
restore only when the communicator path is restored)
•
4 Blinks:
RF trouble (antenna connection or cellular
registration)
•
5 Blinks:
Communicator poll or check
-
in failure
(cellular and/or IP). Either or both paths will trigger the
trouble, but for the trouble to clear, unit requires that
the previously active path(s) must restore (i.e. cellular if
used as a Sole Path communicator, and both cellular
and IP if unit is used as a Dual Path communicator)
•
6 Blinks:
Unit disabled (reporting or control panel
downloading not allowed). Power cycle the unit and if
it does not clear, then call for Technical assistance.
•
7 Blinks:
Unit was shut down and has no functionality;
requires a restart (full power down and full power up
NOTICE TO AUTHORITIES HAVING JURISDICTION, USERS, INSTALLERS,
DEALERS, AND OTHER AFFECTED PARTIES
FIRE PROGRAMMING OPTION
PERMITTED IN
UL864? (Y/N)
AVAILABLE SETTINGS
REQUIRED UL 864 SETTINGS
Unattended Remote Downloading
No
Enable / Disable
Disabled (Jumper 1 installed). Also required for Commercial installations.
Note:
See page 7 "
Configuration Download / Firmware Updates
" for jumper instruc-
tions.
IN2
and
IN3
Unsupervised
Yes
Supervised / Unsupervised
Unsupervised using conduit within 20 feet of FACP (default). If not using conduit,
install Jumpers 4 and 5 and EOL Resistors. Inputs 2 an 3 can be unsupervised
with jumpers 4 and 5 removed; IN4 and IN5 always require EOLR.
7 Day Supervision, Communicator
to NOC
No
200 seconds, 5 minutes, 6
minutes, 60 minutes, 6
hours, 7 days
200 seconds, 5 minutes, 60 minutes. 6 Hours permitted in Commercial Fire UL
864 with Dual Path enabled.
Trouble on Communicator or IP
Path (Annunciate / Report)
Yes
Either Path or Both Paths Either Path (annunciation and report of trouble).
Wi-Fi Module
Yes
Enable / Disable
May be enabled as a primary reporting path for Fire.
LED LOCATIONS
D4 D3 D5
RED DIAGNOSTIC LED ("
D7
")
•
YELLOW
OPERATIONAL
STATUS LED ("
D4
")
•
GREEN RF SIGNAL
STRENGTH LED
("
D3
")
•
RED TROUBLE LED
("
D5
")
IP Communication LEDs