1
GEM-PXCV
Proximity Reader Cover
Installation Instructions
R
333 Bayview Avenue
Amityville, New York 11701
For Sales and Repairs, (800) 645-9445
For Technical Service, (800) 645-9440
© Napco 2004
WI1279 6/04
GENERAL DESCRIPTION
The GEM-PXCV is a durable hard plastic snap-on cover de-
signed to replace the standard cover of the HID Model 6005B
proximity card reader when used with a GEM-ACM1D Ac-
cess Control System. These instructions detail the mounting
and wiring procedures for the reader, and the installation of
the GEM-PXCV cover.
There are 3 LEDs associated with this combination:
•
The HID Model 6005B LED which provides the status of
the
access condition
(door "locked" or "unlocked"). See
Table 1.
•
Two LEDs within the GEM-PXCV which provide the status
of the
system condition
(system "armed" or "disarmed")
associated with the access Area (see Table 2).
Together, the GEM-PXCV is an indoor/outdoor proximity
card reader providing potted electronics, low power con-
sumption and durability all in a small, easy-to-install package.
LED Indications
The HID Model 6005B reader contains a multicolored LED
which provides visual
feedback as to access
condition when access
cards are presented to
the reader.
Table 1 below displays
the LED indications and
their meanings.
The GEM-PXCV module
provides two LED's to
indicate system status,
as displayed in Table 2
below:
Stealth Mode
is used to hide the ACM’s Armed and Status
LEDs. When
Stealth Mode
is enabled, the GEM-PXCV sys-
tem status LEDs are normally off but are turned on for 1 min-
ute by any of the following events:
•
Press a request to exit button
•
Press a request to arm button
•
Present a valid ARM/DISARM or ARM card to the reader
When Stealth Mode is disabled ("normal operation"), the
LED's are always enabled and mimic the Keypad Status
LEDs for the following functions only:
Armed
,
Disarmed
,
Ready to Arm
,
Not-Ready to Arm
and
Alarm
.
Note:
When
the system is in alarm, Stealth Mode is disabled. "Access
Only" cards do not affect the status of Stealth Mode.
MOUNTING THE GEM-PXCV
Before mounting the card reader, always plan ahead and deter-
mine the route all wires will follow before drilling into wall mount-
ing surfaces. For more information regarding various system
designs, refer to WI1121 for complete installation instructions.
Install the GEM-PXCV as follows:
Table 3: Proximity Card Reader Connections
GEM-ACM1D Termi-
nal Number
GEM-ACM1D Terminal
Description
HID Model 6005B (Prox Point
Plus ) Wires
17 (+)
Reader Power
Red (+ DC)
18 (-)
Reader Power
Black (- Ground) & (Shielded
Ground)
19
Reader Data 1
White (Data 1)
20
Reader Data 0
Green (Data 0)
21 (-)
Red LED
Brown (Red LED)
22 (-)
Red & Green LED
Orange (Green LED)
23 (-)
Reader Sounder
Yellow (Beeper)
(Not Used)
(Not Used)
Blue (Hold)
(Not Used)
(Not Used)
Violet (Card Present)
* Tamper Connection not available on HID 6005B
Be sure to place jumper JP1 in correct configuration for 5 volt or 12 volt reader
operation.
Table 1: (Top) Access Status LED (HID Model 6005B)
LED INDICATION
ACCESS CONDITION
Steady Red
Door Locked
Steady Green
Door Unlocked
Momentary Green
Card Read--Door Remains Locked
Alternating Green & Red
(Downloading PCD-Windows Program to ACM)
Table 2: (Bottom) System Status LED's (GEM-PXCV)
LED INDICATION
SYSTEM CONDITION
Steady Red
System Armed
Red LED is off
System Disarmed
Blinking Red
System in Alarm
Steady Green
System Ready to Arm
Green LED is off
System Not Ready to Arm
Table 4: GEM-PXCV Wire Connections
GEM-PXCV Wires
GEM-ACM1D
Terminal
Description
GEM-ACM1D
Terminal Number
GEM-2D Terminal
Number
Red
Reader Power
17 (+)
35 (+)
Orange
Active Low Red
Armed LED
30
48
Green
Status Green LED
31
49
System
Status LED's
(see table 2)
Access
Status LED
(see table 1)
