WWW.NAKAYAMATOOLS.COM
4
EN
EN
WWW.NAKAYAMATOOLS.COM
5
Recommended mixing ratio: gasoline 25:oil 1
Operation
Starting The Engine
Before starting the engine, inspect the entire unit for loose fillings or duel and the
cutting attachments is properly installed and securely fastened.
• Place the unit on a flat, firm place. Keep the cutting head clear of everything around it.
1. Turn the cap to the fuel tank to make sure that it is fixed on tightly.(F8)
(1) Cap
(2) Fuel tank
2. Open the fuel tank cock. (F9)
3. Move the choke lever to the closed position. (F9)
(1) Choke lever
(2) Fuel cock
(3) Close
(4) Open
(5) Close
(6) Open
When restarting immediately after stopping the engine, move the choke lever to the open position.
4. Set the throttle lever to the starting position. (F10)
(1) Idling
(2) Starting( l/3~1/2 open)
(3) Full throttle
When restarting immediately after stopping the engine, move the throttle
to the idling position.
5. While holding the unit firmly, pull out the starter rope quickly. (F11)
6. After the engine has started, open the choke gradually.
7. Allow the engine to run for 2 to 3 minutes to warm up.
Stopping The Engine
1. Return the throttle lever to the idling position.
2. Push the engine switch button.
Equipping The Shoulder Band (F12)
1. Equip the attached shoulder band.
2. Turn on the engine, return the throttle lever to
the lowest speed position, and Put the shawl band
hook to the hanging pan of the machine ..
3. Adjust the length of the shawl band so that the
blade may be parallel to the ground in the working
position. In order to prevent slack during operation, turn up the extra pan of the band from
the buckle.
Cutting Operation
Metal Blade Usage
• Always cut by guiding the head from your right to left.
• A .metal blade cut best up to the point 1/3 from the edge. Use that area for shrubs, tough and
thick weeds. For cutting young grass, you can use up to 2/3 from the lip of blade.
• Adjust the engine speed according to the cutting objects. Cut the young grass at middle speed, and
cut shrubs or tough and thick weeds at high speed.
(1) For branches and trees
(2) For grass and weeds
(3) Direction of cutting
(4) Direction of rotation
Important:
Operating at low speed makes it easier for grass, weeds, or twigs to become caught up in
the blades, and also it makes the shaft and clutch wear down more quickly.
Summary of Contents for Pro PB7300
