background image

Page 2 of 14

4/21  IOM-MAC-700-INST

Nailor Industries Inc. reserves the right to change any information concerning product or specification without notice or obligation.

CRITICAL OPERATION CONDITIONS OF THE MOBILE AIR CLEANER UNIT W / HEPA FILTER

• 

DO NOT TOUCH 

the HEPA filter media. Damage to filter media may void the filter warranty. The screen is to protect against 

accidental contact with the filter. Never place objects on the filter. Always transport or lift the filter by its frame. 

•  Prior to powering the unit, verify that it is wired to the correct power supply. The rating plate label located on the electrical 

box cover shows the electrical data.

•  For replacement parts refer to the model number and serial number on the rating plate label located on the electrical box.

REPLACEMENT PART NUMBERS

When ordering replacement parts, please include unit model & serial number and P.O.# if available.

WARNING  – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO 

PERSONS; ALLOW ONLY QUALIFIED TECHNICIANS TO INSTALL AND SERVICE THE 

UNIT. ALL PERSONS SHOULD OBSERVE THE FOLLOWING:

a)  Before servicing or cleaning unit, disconnect and lock-out power at the service panel to prevent electric shock or 

injury if the power is accidentally turned on. 

 

Installation work and electrical wiring must be completed by qualified persons in accordance with all applicable 

codes and standards.

•  If this unit is to be installed within close proximity to water, mark the unit in accordance with applicable codes and 

standards.

•  This unit is to be used only as intended by the manufacturer. If you have any questions regarding the use, installation 

or operation of this unit; contact the manufacturer:

  Nailor Industries of Texas, Inc.

  4714 Winfield Road, Houston, TX 77039

  Tel.: 281-590-1172

 nailor.com

Part #

Part Description

V H1-1791

Motor

V H1-0900

Blower

MAC700HEPA

24 x 24 x 6 (610 x 610 x 152) HEPA Filter

MAC700PREFILTER

24 x 16 (610 x 406) Pre-Filter

MACUVC20

UV Light

V H1-3004

UV Light Ballast

V H1-3017A

Safety Interlock Switch

V H1-2964

0 - 10 V Speed Controller

V H1-3003 A, B, C & D

Illuminated ON / OFF Switch

V H1-3016

UV-C Hour Counter

Summary of Contents for MAC-700















Reviews: