background image

ENGLISH

OPERATION

13

STANDBY MODES

STANDBY MODE

CONDITION

RESULT

Standby Mode 1

(Power Button)

Method A

•  ECO mode : ON

•  Power mode: Switch from other Power Mode (Always ON, 12V Trigger, 

Signal Sense) to Power Button

•  Unit will immediately go to standby mode after the switch to Power 

Button mode.

Method B

•  ECO mode : ON

•  Power mode: Currently at Power Button and unit at operating mode

•  Unit will immediately go to standby mode when front panel Standby 

button is pressed.

Standby Mode 2

(12V Trigger)

Method A

•  ECO mode : ON

•  Rear panel 12V TRIGGER switch: ON

•  Power mode: Switch from other Power Mode (Power Button, Always ON, 

Signal Sense) to 12V Trigger

•  Unit will immediately go to standby mode after the switch to 12V 

Trigger mode.

Method B

•  ECO mode : ON

•  Rear panel 12V TRIGGER switch: ON

•  Power mode: Currently at 12V Trigger and unit at operating mode 

•  Unit will immediately go to standby mode when 12V TRIGGER source is 

turned off.

Standby Mode 3

(Signal Sense)

Method A

•  ECO mode : ON

•  All Sources are powered down or no signal output

•  Power mode: Switch from other Power Mode (Power Button, Always ON, 

12V Trigger) to Signal Sense

•  Unit will immediately go to standby mode after the switch to Signal 

Sense mode.

Method B

•  ECO mode : ON

•  All Sources are powered down or no signal output

•  Power mode: Currently at Signal Sense and unit at operating mode 

•  Unit will go to network standby mode after 20 minutes of no active 

audio source input.

Network Standby Mode 1

(Power Button)

Method A

•  ECO mode : OFF

•  Power mode: Switch from other Power Mode (Always ON, 12V Trigger, 

Signal Sense) to Power Button

•  Unit will immediately go to standby mode after the switch to Power 

Button mode.

Method B

•  ECO mode : OFF

•  Power mode: Currently at Power Button and unit at operating mode

•  Unit will immediately go to network standby mode when front panel 

Standby button is pressed.

Network Standby Mode 2

(12V Trigger)

Method A

•  ECO mode : OFF

•  Rear panel 12V TRIGGER switch: ON

•  Power mode: Switch from other Power Mode (Power Button, Always ON, 

Signal Sense) to 12V Trigger

•  Unit will immediately go to network standby mode after the switch to 

12V Trigger mode.

Method B

•  ECO mode : OFF

•  Rear panel 12V TRIGGER switch: ON

•  Power mode: Currently at 12V Trigger and unit at operating mode 

•  Unit will immediately go to network standby mode when 12V TRIGGER 

source is turned off.

Network Standby Mode 3

(Signal Sense)

Method A

•  ECO mode : OFF

•  All Sources are powered down or no signal output

•  Power mode: Switch from other Power Mode (Power Button, Always ON, 

12V Trigger) to Signal Sense

•  Unit will immediately go to standby mode after the switch to Signal 

Sense mode.

Method B

•  ECO mode : OFF

•  All Sources are powered down or no signal output

•  Power mode: Currently at Signal Sense and unit at operating mode 

•  Unit will go to network standby mode after 20 minutes of no active 

audio source input.

Summary of Contents for CI 8-120 DSP

















Reviews: