background image

 

 

 

5

 

 

In  all  cases,  obey  the  Traffic  Regulations  and  remember  that  riding  your 

motorcycle has absolute priority over any other manoeuvre. 

 

Adjust  the  volume  to  a  level  that  does  not  disturb  or  distract  you  while 

riding  and  at  the  same  time  allows  you  to  distinctly  heal  background 
noises. 

 
Caution:  Adjust  the  volume of  the  N-Com system  (where provided) and  of 

the audio sources connected to it before you use it on the road. 

 
Caution:  Adjusting  the  volume  to  very  high  levels  may  cause  damage  to 

your hearing  

Caution:  Adjust  the  volume of  the  N-Com system  (where provided) and  of 

the audio sources connected to it so as to avoid audio reproduction at high 
volumes. Constant exposure to high volumes may damage your hearing.  

 
Caution:  Improperly  installing  the  system  in  the  helmet  may  alter  the 

aerodynamic  and  safety  properties  of  the  helmet  itself,  thus  creating 
dangerous  conditions.  Install  the  N-Com  system  according  to  the 
instructions  provided  in  the  product  documentation.  In  case  of  doubt, 
contact our local N-Com dealer.  

 

 

All telephones and devices with wireless signal transmission are subject to 

interferences that may affect the performance of the device connected 
to  them.  These  interferences  are  not  ascribable  to  a  defect  of  the  N-
Com system. 

 

Use  the  device  in  the  normal  position  only,  as  described  in  the  product 

documentation. Do not attempt to disassemble, tamper with or modify 
any part of the N-Com system.  

Summary of Contents for MCS II

























Reviews: