background image

 

 

 

21

 

Nolangroup  shall  not  be  responsible  in  case  the  product  presents  limited  capabilities  due  to  the 
operating mode of cell phones or of other accessories or equipment not supplied by Nolangroup. 
Tampering with the internal electronic card or with other parts of the N-Com system shall invalidate 
the warranty. 
Moreover,  the  defects  covered  by  this  warranty  do  not  include  all  those  specific  and  subjective 
situations  that  may  come  up  during  the  active  use  of  the  helmet  such  as,  for  example,  comfort 
problems while riding or aerodynamic noises. 
Nolangroup  shall  not  be  held  responsible  in  any  case  for  incidental  or  consequential  damages 
(including,  without  any  limitation  whatsoever,  damages  to  one  or  more  persons)  resulting  from 
non-fulfillment of the obligations arising from this warranty as it pertains to Nolangroup products. 
 

7.3.

 

Validity of this limited warranty 

This warranty is valid only if the enclosed warranty form is duly and completely filled out with the 
following information: 

 

Product identification code 

 

Name and stamp of the authorized dealer. 

 

Product purchase date. 

 

Buyer’s name and address. 

Nolangroup reserves itself the  right to not carry out repairs  under  warranty if the  aforementioned 
information is removed or modified after the original purchase of the product from the dealer. 
 

7.4.

 

Procedure for the forwarding of claims 

To forward a claim covered by this warranty, the buyer has to directly notify the dealer where the 
helmet  was  purchased  with  regards  to  the  defect,  presenting  at  the  same  time  the  defective 
product, a copy of the sales receipt and the Warranty registration form, duly filled out as instructed 
above. 
PRIOR  TO  CONTACTING  THE  DEALER,  WE  RECOMMEND  THAT  YOU  READ  CAREFULLY  THE  USER 
MANUAL ENCLOSED WITH THE PRODUCT. 
AFTER  2  (TWO)  YEARS  FROM  THE  DATE  OF  PURCHASE,  THIS  LIMITED  WARRANTY  IS  VOID  FOR 
ALL EFFECTS AND PURPOSES. 
Repairs or maintenance under warranty do not extend the period of the warranty itself. Therefore, 
in  case  the  product  or  one  of  its  components  is  replaced,  this  does  not  initiate  a  new  warranty 
period,  as  the  purchase  date  of  the  original  product  shall  be  taken  into  account  for  warranty 
purposes. 
Only for repairs or replacement of electronic components, in the event that Nolangroup proceeds to 
repairing or replacing the product, said product shall enjoy a warranty period equal to the residual 
portion of the original warranty or  ninety (90)  days from the repair date (the longer period being 
considered). 

Summary of Contents for MCS II

























Reviews: