background image

 

 

 

19

 

Warning: Connect the cables so that they are free and do not hinder riding 

nor  reduce  the  freedom  of  movement,  and  do  not  wind  them  around  the 
limbs, bust or neck. Do not lock the connectors so that, if necessary, they 
can be easily disconnected. 

 
Warning:  While  using  the  connection  cable,  always  use  helmets  provided 

with a visor, and keep the visor in lowered position  

 
 

6.

 

MAINTENANCE 

The N-Com does not require any special maintenance tasks.  
In  case  you  use  the  kit  when  it  rains,  dry  off  the  wet  parts  of  the  helmet, 
paying special attention to the contact area. 
 
In case the system get wet several times, rust or corrosion may form which 
damage the electrical contact. 
  
If  this  happens,  it  is  recommended  to  clean  the  contacts  of  the  connector 
secured to the shell, using alcohol or another anti-rust product. 
 
 

7.

 

LIMITED WARRANTY 

With  this  LIMITED  WARRANTY  CERTIFICATE,  Nolangroup  warrants  this  Product  to  be  free  from 
defects in material and workmanship at the time of its original purchase by the buyer. 
We invite you to: 

Read the cautions pertaining to safety and proper use. 

Read the warranty terms and conditions. 

Keep  the  originals  sales  receipt.  This  must  be  shown  in  case  of  repairs  covered  by 

warranty. In these cases, the product has to be taken back to the dealer where it was purchased. 

Summary of Contents for MCS II

























Reviews: