manualshive.com logo in svg

Mychef QUICK 1T, Product Manual

Share
Download
Mychef QUICK 1T Product Manual Download Page 29

 

 

mychefcooking.com 

PRODUCT MANUAL     QUICK 1T     -     DT.MP.Q1T.2202.2 

 

29 

7.

 

USE 

This section will give an overview of the basic functions and all the information necessary for 
the correct use of the user interface of the Mychef QUICK 1T oven.  

 

7.1.

 

Switching on the equipment 

The equipment is switched on or off by pressing the circular button (START/STOP) for a few 
seconds. 

 

 

In  order  to protect the  oven  from  possible  overheating,  some  protection 
elements may operate even when the oven is switched off. When the oven 
is at a safe temperature, they will automatically switch off. 

 

If the unit does not turn on, check the condition of the safety thermostat, located on the back 
of the unit. To do this,  first remove a black plastic plug located next to the power cable 
gland.  

 

 

Figure 19. Access to the safety thermostat 

 

7.1.1.

 

First use 

Once  you  have  connected  your  Mychef  oven  for  the  first  time,  the  corresponding 
parameters must be set (Section 6.2). The oven is then ready for operation. 

 

 

 

 

Summary of Contents for QUICK 1T



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands