background image

6

3. USAGE PRECAUTIONS

3-1. Power Supply

This equipment shall be installed near the socket-outlet where the plug on the power supply
cord is easily accessible.

Make sure the power supply used is always within the following range.

100 to 240 V AC, 50/60 Hz

When you power other appliances from the same AC outlet, make sure that the combined
power consumption does not exceed the power supply capacity.

Rated power of this equipment: 1.4 to 0.7 A (95 W)

3-2. Operating Environment

Operate this unit in the following environment:

– where the temperature range is between 41 and

95

°

F,

– where the humidity range is between 20 and

80% RH (no dew condensation),

– which is not subject to direct sunlight,

3-3. Storage Conditions

Store this unit in the following environment:

– where the temperature range is between 14 and

122

°

F,

– where the humidity range is between 10 and

85% RH (no dew condensation),

– which is not subject to direct sunlight,

3-4. Maintenance

To protect the special features of this unit, the customer should never apply oil or grease to the
parts. Please contact your dealer in case of any problem.

– which is subject to little or no vibration,
– where there are no harmful chemicals,
– which is reasonably free from dust,
– which is free from air-borne salt, and
– where the equipment is not exposed to water.

– which is subject to little or no vibration,
– where there are no harmful chemicals,
– which is reasonably free from dust,
– which is free from air-borne salt, and
– where the equipment is not exposed to water.

Do not use flammable sprays or solvent inside or near the unit (e.g. when cleaning the
unit). Such flammable gas may ignite and cause a fire or combustion. Such solvents may
damage the rubber rollers and resin inside the unit, resulting in malfunctions.

WARNING

!

Summary of Contents for Duplo DF-915


































































Reviews: