background image

1.0  Introduction 

 

 
2

 

1.0 Introduction 

THIS MANUAL is designed to help you get the most from your Challenge equipment.  Keep this 
manual in a safe, convenient place for quick reference by operators and service personnel. 
 

 

SAFETY ALERT!  

This symbol means 

CAUTION: Personal safety 

instructions!  

Pay special attention to the instructions in bold type.  Personal injury may result if the 

precautions are not read and followed. 
 

READ THIS MANUAL BEFORE OPERATING!  

Follow precautions and instructions.  If after reading 

the manual questions still remain, contact your Authorized Challenge Dealer. 
 
Take a few minutes right now to 

RECORD YOUR MACHINE SERIAL NUMBER 

in the space 

provided on the front cover of this manual.  Also be sure to fill out the warranty card accompanying 
your machine and return it 

DIRECTLY TO CHALLENGE.

 

 
If you bought a used machine, it is important to have the following information on record at Challenge.  
Copy this page, fill in the information and send it care of The Challenge Service Department, 6125 
Norton Center Drive, Norton Shores MI.  49441.  
 
 

CHALLENGE MODEL   

SERIAL NUMBER 

ATTN COMPANY 
 
ADDRESS 
CITY STATE/PROVINCE 

ZIP 

PHONE DATE 

INSTALLED 

DEALER NAME & CITY 

 

 
 

* WARRANTY INFORMATION * 

 

It is very important that you read and understand the conditions outlined in the 

Warranty Information 

Sheet 

attached to the outside of the shipping container of your machine. 

 
The 

Warranty Information Sheet

 must be filled out completely and returned to THE CHALLENGE 

MACHINERY COMPANY in order for the warranty to be issued for this machine. 

 
 
 
 
Challenge® is a registered trademark of The Challenge Machinery Company

 6125 Norton Center Drive

 Norton Shores MI.  

49441 Copyright© 2004 by The Challenge Machinery Company.  All rights reserved.  Printed in the U.S.A 
 
 
 
 
 
 
 
 
 
 

 

Summary of Contents for CHALLENGE SPARTAN 150SA



























Reviews: