MuxLab MuxStream 500930 Operation Manual Download Page 7

Page: 7 / 47

MuxStream Camera Operation Manual

Specification

Camera

Sensor

1/2.7 inch, CMOS, Effective Pixels: 2.07M

Scanning Mode

Progressive

Lens

12x, focal length of 3.5mm to 42.3mm, F-Stop of 1.8 to F2.8

Digital Zoom

16x

Minimal Illumination

0.5 Lux @ (F1.8, AGC ON)

Shutter

1/30s to 1/10000s

White Balance

Auto, Indoor, Outdoor, One Push, Manual

Backlight Compensation

Supported

Digital Noise Reduction

2D & 3D Digital Noise Reduction

Video S/N

≥55dB

Horizontal Angle of View

72.5° to 6.9°

Vertical Angle of View

44.8° to 3.9°

Horizontal Rotation Range -170° to +170°

Vertical Rotation Range

-30° to +90°

Pan Speed Range

1.7° to 100°/s

Tilt Speed Range

0.7° to 28°/s

Horizontal & Vertical flip

Supported

Image Freezing

Supported

Number of Presets

255

Preset Accuracy

0.1°

IPC Features

Video coding standard

H.265/H.264/MJEPG

Video Stream

First Stream, Second Stream

First Stream resolution

1920x1080,1280x720,1024x576,960x540,640x480,640x360

Second Stream resolution

1280x720,1024x576,720x576,720x408,640x360,480x270,320x240,3

20x180

Video Bit Rate

32Kbps to 20480Kbps

Bit Rate Types

Variable bit rate and Fixed bit rate

Summary of Contents for MuxStream 500930
















































Search results

Summary of Contents for MuxStream 500930

Reviews:

Related manuals for MuxStream 500930

Brands by name

Popular brands

MuxLab MuxStream 500930, Operation Manual

Search results

Summary of Contents for MuxStream 500930

Reviews:

Related manuals for MuxStream 500930

Brands by name

Popular brands