© MuxLab Inc.
94-000836-B SE-000836-B
8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5
Tel: (514) 905-0588 Fax: (514) 905-0589
Toll Free (North America): (877) 689-5228
E-mail: [email protected] URL: www.muxlab.com
Specifications
Environment
HDMI 1.4
Devices
Computers and servers with HDMI monitor ports.
Transmission
Transparent to the user
Bandwidth
300MHz
Signals
HDMI 1.4 protocol, HDCP 1.4
Connectors
Note: Cables not included.
One (1) HDMI receptacle.
One (1) RJ45S for Cat 5e/6 unshielded or shielded twisted pair.
Two (2) 3.5mm jacks for audio insert (on TX)/audio extract (on RX).
Two (2) 3.5mm jacks for mic-out (on TX)/mic-in (on RX).
One (1) 2.1mm locking barrel jack for power
One (1) or Four (4) USB Connector(s) for Host (on TX)/Client (on RX)
Four (4) DIP Switches for device ID addressing.
Maximum Distance
Based on a maximum length
of 6.6ft (2m) of HDMI cable
per end.
Cat5e/6: 330ft (100m) up to 1080p @ 60Hz and 1920x1200 @ 60Hz
Note: When installed in an electrically noisy environment, an STP cable must be
used. Also, cross-connection reduces the effective distance depending on the grade
of twisted cable used.
Latency
One (1) Frame (16ms) @ 60Hz (typical)
Compression
JPEG 2000
Network Bit Rate
300Mbps (typical)
Network Requirement
1000BaseT with PoE
RJ45 Pin Configuration
Reverse Polarity Sensitive.
Use EIA/TIA 568A or 586B
straight-through wiring.
RJ45 Link
Pin 1 (R)
Pin 2 (T)
Pin 3 (R)
Pin 6 (T)
Pin 4 (R)
Pin 5 (T)
Pin 7 (R)
Pin 8 (T)
Cable
One (1) Cat 5e/6 or better twisted pair cables required
Power Source
This device supports PoE (PD), an external power supply is not included. It is
intended to be powered via a PoE (PSE) Ethernet Switch. If required, an optional
power supply (500993) may be purchased separately.
PoE Standard
IEEE 802.3af
Power Consumption
Transmitter: 2.85Watt
Receiver: 2.55Watt
Temperature
Operating: 0° to 40°C
Storage: -20° to 85°C
Humidity: Up to 95% non-condensing
Dimensions
4.40” x 5.08” x 1.00” (112mm x 129mm x 25mm)
Weight
1.5lbs (0.68kg)
Compliance
Regulatory: FCC, CE, RoHS
Flammability: 94V0
Warranty
3 years
Order Information
500770
KVM HDMI over IP PoE Extender Kit
500770-TX KVM HDMI over IP PoE Extender TX
500770-RX KVM HDMI over IP PoE Extender RX
Accessories
(These items are sold
separately)
500920 16-Port Rackmount Transceiver Chassis
500917 Wall Mount Transceiver Bracket Kit
500993 Univ. Locking Power Supply 5VDC/2.6A US/UK/EU Blade
KVM HDMI over IP PoE Extender Kit
500770
Quick Installation Guide
Overview
The KVM HDMI over IP PoE Extender Kit allows HDMI & USB equipment to be connected up to
330ft (100m) up to 1080p resolution @ 60Hz and 1920x1200 @ 60Hz via one (1) Cat5e/6
unshielded twisted pair cable in a point-to-point configuration. The Transmitter (500770-TX) and
Receiver (500770-RX) also support PoE (PD) if used with a PoE (PSE) Ethernet Switch. The kit
comes with one (1) Transmitter and one (1) Receiver. Additional Transmitters and Receivers may
be purchased as kits or purchased separately depending on the number of units required.
For the multiple point-to-point (including point-to-multipoint) configurations the Ethernet Switch
must have Gigabit ports, Jumbo Frame capability and DHCP Server capability. MuxLab
recommends using the Cisco SG300 Series Managed Switches.
The MuxLab ProDigital Network Controller (500811) is available to simplify the configuration and
utilization of the 500770 and other MuxLab IP based products via an Ethernet web interface.
Applications
Applications include management of multi-server systems supporting HDMI displays in IT
departments within corporations, educational institutions, CAD Design, Graphic Design, Media
Servers, and Data Centers.
Installation
1.
Identify the connectors on the Transmitter and Receiver as indicated on the product labels, see the
above front and rear product views for further details.
2.
Verify that the distance between the HDMI Transmitter and Receiver is within MuxLab
specifications (see Specifications table for more details).
3.
To install the Transmitter:
3a.
Connect the Transmitter to the HDMI video source with an HDMI compliant cable.
3b.
Connect the Transmitter USB Port to the Computer USB port, using a compliant Type
A to Type B USB Cable.
3c.
If required, connect the computer audio-out and mic-in port to the Transmitter audio-in
and mic-out port, respectively.
3d.
If the application is point-to-point, then connect one (1) length of Cat 5e/6 (or higher)
grade UTP cable to the RJ45 LINK connector on the Transmitter. If transmitting over
the network, use an Ethernet Switch between Transmitter and Receiver.
