MUTOH VJ-628 ValueJet Operation Manual Download Page 6

Page: 6 / 80

6 Name of each part

Introduction

Name of each part

Printer’s main body

Operation panel

Introduction

Network connector

Connect an Ethernet cable.

Voltage selector switch

Scroller receivers

Mount a roll media

Cartridge slots

Install an ink cartridge or
cleaning cartridge.

Operation panel

⇒

Operation panel

Platen

Media is printed on here.
There are an adsorption fan
and a heater inside.

Media pressure arm

Hold media to the platen. It
links with the media fixing
knob.

Front cover

Open when mounting media
or during maintenance.

Media fixing knob

Turn when mounting and
removing media.

Waste liquid tube

Waste ink is drained from the
tube.

Paper guides

When attached on both
edges of media, a curvature
of media can be controlled to
some extent.

Carriage

A print head and cutter are
built-in.

Power connector

Error LED

Red light or flashing displays

errors or warnings.

Power button

It lights ON in blue when the

power is ON.

Operation key

Used for various functions in different situations.

Printing:

(Short press) Pause/Restart printing
(Long press) Cancel printing (data deletion)

Waiting for printing:

(Long press) Cut media

When linked with VSM and waiting to be confirmed:

(Short press) Confirm

While Warming up:

(Short press) Force starting printing

During forwarding/rewinding media:

(Short press/Long press) Stop forwarding/rewinding

During error:

(Short press) Stop the buzzer

Data LED

Green flashing indicates

receiving and analyzing state

of printing data.

Summary of Contents for VJ-628 ValueJet

















































































Search results

Summary of Contents for VJ-628 ValueJet

Reviews:

Brands by name

Popular brands

MUTOH VJ-628 ValueJet, Operation Manual

Search results

Summary of Contents for VJ-628 ValueJet

Reviews:

Brands by name

Popular brands