manualshive.com logo in svg

MUTOH VJ-626UF, Operation Manual

Share
Download
MUTOH VJ-626UF Operation Manual Download Page 136

136     Boot-up troubleshooting

"Initial 4: IP Address" on page 77

, 

"Initial 5:Subnet Mask" on page 77

, 

"Initial 6: Gateway" on page 78

 “Ensuring a suitable place for installation” of the “Startup Guide” on page P.5

Boot-up troubleshooting

VSM or RIP cannot access to
the printer.

Is Ethernet cable connected correctly?

‐ Securely connect the Ethernet cable to the Ethernet Port.

Are the network settings configured correctly?

‐ Configure the network settings correctly.

Do the printer’s network settings match the computer’s settings?

‐ Match this product’s network settings with the computer side environment.

Does not work at all
after power activation /
after loading the media.

Is the power cable connected to the plug?

‐ Connect the power cable.

Does the AC power supply provide the specified voltage?

‐ Connect the cable to another outlet.

Is the front cover, or the maintenance cover open?

‐ Close the front cover, or the maintenance cover.

Is there any error message displayed on VSM?

‐ Go to the Printer Status tab in VSM and check that if any error message is displayed in 

the Status Information.

Do you use the printer within recommended environmental conditions?

- Make sure to use the printer within the specification range.

Summary of Contents for VJ-626UF

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands