manualshive.com logo in svg

MUTOH VJ-626UF, Operation Manual

Share
Download
MUTOH VJ-626UF Operation Manual Download Page 130

130     Status messages

4

Messages and Error Messages

This section describes messages displayed during normal printer operation or when errors occur, and solutions to the messages.

This section describes messages displayed during printer normal operation.
When the printer is operating correctly, each operation status is displayed on the operation panel as below.

Status messages

Display

Description

Activation required

Activation has not been executed.
Consult the relevant section of the Startup Guide, and carry out activation.

 “Step1 Carrying out activation” of the “Startup Guide” on page P.29

Ready to Print

Standby (Media is loaded).

Set media, then
press Set Media Key

Standby (Media is not loaded).

Receiving

Receiving data.

Processing

Analyzing data.

Printing

Under printing.

Remain : XXX.Xm

Displays the length of the data that has not been printed in meters for the 
data currently being printed.

Remain Time : XXX.Xmin

Displays the time remaining to print in minutes for the data currently being 
printed.

PrintRestart->Enter

Printing is paused. To resume, press the [Enter] key.

Power Off

Turning OFF the printer. Wait for a while.

S/C Reading

Reading the S/C card.

Ink Circulation

Ink is circulating inside the printer.

*** Remote Mode ***

The remote panel mode is running, via VSM or similar. In the remote panel 
mode, operations via the operation panel are not possible. To terminate the 
remote panel mode, press the [Cancel] key for more than two seconds.

Start Ink Charge ->E

Ink charging starts.
Please wait a while.

Insert CleaningCart.

Washing Print head.
Install the cleaning cartridges.

Busy-Washing **%

• Initial charging, ejecting filler fluid.

• Washing the print head by cleaning fluid.

Please wait a while.

Remove Cartridges

Washing Print head or discharging ink.
Remove the cartridges.

Insert Ink Cartridges

Charging the ink.
Insert Ink Cartridges

Ink Refill **%

Charging the ink.
Please wait a while.

Discharging

Discharging the Ink.
Please wait a while.

Messages and Error Messages

Summary of Contents for VJ-626UF

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands