MUTOH ValueJet VJ-1624WX Operation Manual Download

Page: 339 / 358

VJ-1624X/1624WX/1924WX OPERATION MANUAL

7 Troubleshooting

7.3 The media is jammed

339

7.3

The media is jammed

When the set media is jammed, follow the procedure below to remove it.

1. Turn OFF the power of the printer.

3.2.2 Turning the power OFF

2. Open Front cover.

3. Move Print head section from the top of the media to the right.

NOTE

When the head height is set to Low, change it to High and then shift Head.
After shifting Head, change the setting back to Low.

4.2.5.2 When setting the head height to High

4.2.5.3 When setting the head height to Low

No.

Name

Front cover

No.

Name

Print head section

Roll media

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands

MUTOH ValueJet VJ-1624WX, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands