MUTOH ValueJet VJ-1624WX Operation Manual Download | Manualshive

Page: 31 / 358

background image

VJ-1624X/1624WX/1924WX OPERATION MANUAL

2 Product overview

2.1 Names of parts and functions

31

2.1.3

Operation panel

Used to set the operating conditions, to display the status of the printer, and to set various functions.
Explains names of each operation key and status display along with the functions.

TIP

•Refer to the following for details regarding the operation method of Operation panel.

•When setting the menu from Operation panel:

4.3 Menu setups on Operation panel

•When performing various operations in Operation panel:

4.4 Operating from Operation panel

(1) Operation keys

NOTE

• Operation keys are assigned with different functions and names depending on the printer status

(Normal or Setup menu display).
For details about the printer status, refer to "

2.2 Printer status outline

".

• The

symbol means “standby”. Even when the power button is not turned on, the printer

consumes a tiny amount of power so long as the power cable is connected. This state is referred to
as the power being “off” in this Manual.

8, 9

3

15

17

16
6

5

11
12

1

13
14

10

2

7

4

«
...
29
30
31
32
33
...
»

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Reviews:

No comments

Related manuals for ValueJet VJ-1624WX

Brand: Felix Storch Pages: 41

Brand: Datamax Pages: 26

Brand: Canon Pages: 4

PIXMA MG3220 series

Brand: Canon Pages: 4

Brand: Canon Pages: 22

Pixma G3020 Series

Brand: Canon Pages: 34

Pixma MG3500 Series

Brand: Canon Pages: 3

Pixma MG7100 Series

Brand: Canon Pages: 4

PIXMA G7000 Series

Brand: Canon Pages: 16

Brand: Canon Pages: 132

Brand: Canon Pages: 62

Brand: Canon Pages: 34

Brand: GE Pages: 16

Brand: Magicard Pages: 108

Brand: Xerox Pages: 70

Brand: Xerox Pages: 6

Brand: Savin Pages: 4

Brand: Rimage Pages: 217

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands