MUTOH ValueJet VJ-1624WX Operation Manual Download

Page: 303 / 358

VJ-1624X/1624WX/1924WX OPERATION MANUAL

6 Maintenance

6.2 Cleaning the printer

303

6.2.4

Cleaning Cleaning wiper

This section describes how to clean Cleaning wiper.

(1) Time for cleaning

Once a week, or when blurs or lacking parts appear on printed media after Head cleaning.

(2) Cleaning procedures

Follow the procedure below to clean Cleaning wiper.

NOTE

Use Cleaning stick to clean Cleaning wiper.
For details of Cleaning stick, refer to

8.3 Options/Supply list

1. If the printer is turned ON, make sure the following.

•

Printing or other operations are not in progress.

•

Operation panel display is Normal.

2. Display the CR Maintenance menu on Operation panel.

a. Press the [Menu] key on Operation panel.

•

"Menu1: Setup>" is displayed on Operation panel.

•

Operation panel shifts to the Setup menu display.

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands

MUTOH ValueJet VJ-1624WX, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands