manualshive.com logo in svg

MUTOH ValueJet VJ-1624WX, Operation Manual

The MUTOH ValueJet VJ-1624WX is a high-quality wide-format printer designed to deliver exceptional print results. With its user-friendly interface, this printer is easy to operate, making it suitable for both beginners and professionals. Enhance your printing experience by downloading the Operation Manual for free at manualshive.com.

Share
Download
background image

VJ-1624X/1624WX/1924WX OPERATION MANUAL

6  Maintenance

6.1  Replacing consumable components

279

6.1.3

Replacing Flushing box sponges

This section explains how to replace Flushing-box sponges.

NOTE

Make sure to install Flushing-box sponges in the printer.
Flushing-box sponges are an essential part to make printing consistent.

(1) Replacement time

Replace Flushing-box sponges in the following situations.

•

When the flushing-box sponge is deformed

•

When the ink is spattered on the media

•

When more than 2 months have passed since the last replacement

•

When ink clumps have accumulated on Flushing-box sponges beyond Flushing-box frame

(2) Type

No.

Name

1

Ink clump

2

Flushing-box frame

Compatible models

Description

Description

VJ-1624X/VJ-1624WX/
1924WX

Flushing-box sponge for VJ-1604

VJ16-FB-SO3

2

1

2

When to replace

OK

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Reviews:

No comments

Related manuals for ValueJet VJ-1624WX

Nanoptix PayCheck Operator'S Manual preview
PayCheck
Brand: Nanoptix Pages: 25
Nanoptix EZ-Tear Cleaning Instructions preview
EZ-Tear
Brand: Nanoptix Pages: 4
Canon LR1 Quick Start Manual preview
LR1
Brand: Canon Pages: 2
Oki B8300 User Manual preview
B8300
Brand: Oki Pages: 95
QMS 4525 Print System User'S Manual preview
4525 Print
Brand: QMS Pages: 180
Xerox DocuPrint 4517 User Manual preview
DocuPrint 4517
Brand: Xerox Pages: 288
Thermotron BC41M Quick Start Manual preview
BC41M
Brand: Thermotron Pages: 10
Olivetti PR4 SL User Manual preview
PR4 SL
Brand: Olivetti Pages: 8
GCC Technologies Elite 21DN+ Getting Started Manual preview
Elite 21DN+
Brand: GCC Technologies Pages: 80
Epson C11CA19201 - WorkForce 30 Color Inkjet Printer Quick Manual preview
C11CA19201 - WorkForce 30 Color Inkjet Printer
Brand: Epson Pages: 36
Epson C11CA19201 - WorkForce 30 Color Inkjet Printer Specification Sheet preview
C11CA19201 - WorkForce 30 Color Inkjet Printer
Brand: Epson Pages: 3
Epson C11C694201 - PictureMate Dash PM 260 Color Inkjet Printer User Manual preview
C11C694201 - PictureMate Dash PM 260 Color Inkjet Printer
Brand: Epson Pages: 72
Epson C11C638001 - LQ 300+II B/W Dot-matrix Printer User Manual preview
C11C638001 - LQ 300+II B/W Dot-matrix Printer
Brand: Epson Pages: 120
Epson C11C640001 - LX 300+II B/W Dot-matrix Printer Reference Manual preview
C11C640001 - LX 300+II B/W Dot-matrix Printer
Brand: Epson Pages: 129
Epson C11CA54203 - PictureMate Show Digital Frame User Manual preview
C11CA54203 - PictureMate Show Digital Frame
Brand: Epson Pages: 106
Epson C11CA19201 - WorkForce 30 Color Inkjet Printer Specifications preview
C11CA19201 - WorkForce 30 Color Inkjet Printer
Brand: Epson Pages: 2
Subli-Trans Xpres SG 3110DNW Instruction Manual preview
SG 3110DNW
Brand: Subli-Trans Xpres Pages: 16
Mitsubishi Electric CP-3800DW User Manual preview
CP-3800DW
Brand: Mitsubishi Electric Pages: 24

Brands by name

Popular brands

Load more brands