MUTOH ValueJet VJ-1624WX Operation Manual Download

Page: 192 / 358

4 Handling the printer

VJ-1624X/1624WX/1924WX OPERATION MANUAL

192

4.4 Operating from Operation panel

4.4.4

Cutting media manually

This section explains how to cut the roll media manually.

Since VJ-1624X is equipped with Heaters, strictly comply with the following Cautions.

CAUTION

• Right after printing, Media guide becomes very hot.

Allow Media guide to cool down before the next operation.

Follow the procedure below to cut the roll media.

1. Verify the following regarding the operational condition of the printer.

•

Printing or other operations are not in progress.

•

Operation panel display is Normal.

2. To change the position to cut the roll media, refer to

4.4.1 Feeding media

and advance the roll

media to the desired cut position.

3. Open Front cover.

No.

Name

Front cover

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands

MUTOH ValueJet VJ-1624WX, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands