Murr Elektronik 55530 Manual Download Page 86

Page: 86 / 156

Configuration/settings

User manual 55530_hdb_en_16

86 / 156

IO-Link event

integration

Fig. 8-24: IO-Link event integration

Type of allocation of IO-Link events to PROFINET diagnostics

Tab. 8-21: IO-Link event integration

Selection

Meaning

= Default

According to IO-Link integration

guideline Edition 1



Standardized IO-Link events are depicted

on standardized PROFINET diagnostics.

Murrelektronik IO-Link integration



Depiction of the IO-Link event number with

the help of mathematical processes on

PROFINET diagnostics.



Events of Murrelektronik devices are avail-

able in plain text.

Murrelektronik IO-Link extended in-

tegration



Depiction of the IO-Link event number with

the help of mathematical processes on

PROFINET diagnostics.



Events of Murrelektronik devices are avail-

able in plain text.



Channel information is available for Mur-

relektronik devices that supports this.

Summary of Contents for 55530





























































































































































Search results

Summary of Contents for 55530

Reviews:

Brands by name

Popular brands

Murr Elektronik 55530, Manual

Search results

Summary of Contents for 55530

Reviews:

Brands by name

Popular brands