Murr Elektronik 55530 Manual Download

Page: 142 / 156

Operation

User manual 55530_hdb_en_16

142 / 156

Tab. 9-23: Diagnostic messages on IO-Link ports according IO-Link integration guide-
line Edition 1

0x10 (16)

0x0020 (32)

0x6230 (25136)
0x6310 (25360)
0x6320 (25376)
0x6330 (25392)
0x6340 (25408)
0x6350 (25424)
0x9811 (38929)
0x9812 (38930)
0x9813 (38931)
0x9814 (38932)
0x9815 (38933)
0x9816 (38934)
0x9817 (38935)

IO-Link master/device: Pa-

rameterization error

Check that the correct IO-Link de-

vice is connected and that only cor-

rect parameters are used.

0x12 (18)

0x0020 (32)

0x5450 (21584)
0x5451 (21585)
0x5452 (21586)
0x5453 (21587)
0x5454 (21588)
0x5455 (21589)
0x5456 (21590)
0x5457 (21591)
0x5458 (21592)
0x5459 (21593)

IO-Link device: A fuse has

blown or is open

Check the IO-Link device.

0x18 (24)

0x0020 (32)

0x5160 (20832) IO-Link device: Outputs

were disabled

Check the devices connected to the

IO-Link device.

0x1A (26)

0x0020 (32)

0x9000 (36864) IO-Link device: Faults with

external resources

Check all resources connected to

the IO-Link device.

Channel

Error Type

Extended Channel

Error Type

IO-Link

event code(s)

Meaning

Action

Summary of Contents for 55530





























































































































































Search results

Summary of Contents for 55530

Reviews:

Related manuals for 55530

Brands by name

Popular brands

Murr Elektronik 55530, Manual

Search results

Summary of Contents for 55530

Reviews:

Related manuals for 55530

Brands by name

Popular brands