manualshive.com logo in svg

Munters TRIO, User And Installation Manual

Share
Download
Munters TRIO User And Installation Manual Download Page 55

 

 

© Munters AB, 2020 

55

 

•

 

Outside temperature: The temperature sensor defined as an outside temperature is not included 
in any average calculation.  

Map specific temperature sensors to specific devices. 

•

 

Go to System > Temperature Definition. 

 

•

 

Map the sensors to devices.  

o

 

Define which sensors are used to calculate the average temperature. 

o

 

Define an outside temperature sensor (if required). 

NOTE

 

Uninstalling a device in the Relay Layout, Analog Output or TRIAC tables removes the device from 

this screen. 

7.2.3

 

E

NABLING A 

W

EATHER 

S

TATION

 

To say costs on temperature sensors, one outdoor temperature sensor can provide data to the entire TRIO 
network.  

NOTE

 

Install and map one outdoor sensor only.  

1. In System > Device and Sensors, define one sensor as Outside Temperature. 

2. Go to System > Control Strategy > Weather Station 

. 

Summary of Contents for TRIO















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands