manualshive.com logo in svg

Munters TRIO, User And Installation Manual

Share
Download
Munters TRIO User And Installation Manual Download Page 132

 

 

© Munters AB, 2020 

132

 

 

12.4.4

 

D

EFINING THE 

W

IND 

C

HILL 

F

ACTOR

 

TRIO can take into account the tunnel wind speed. The effect of this speed is the wind chill factor. When 
taken into account, the ventilation is adjusted to reflect the effective temperature according to a built-in 
algorithm.  The algorithm takes into account the wind velocity, house dimensions, and growth day. If there 
is a humidity sensor installed, the algorithm also factor the relative humidity into the calculation (starting 
from 40% RH). Factoring in the RH lowers the calculated wind chill factor. 

•

 

Wind chill is activated in tunnel mode only. 

•

 

Wind chill calculations take place between days 10 – 50.  

 

Define the fan capacity (refer to Defining the Fans, page 56) 

 

Define the house dimensions (refer to Defining the House Setting, page 97) 

 
1. Go to System > Control Strategy > Ventilation. Scroll down to Wind Chill. 

 

2. Define: 

Summary of Contents for TRIO















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands