MultiMax 6DS User Manual Download Page 11 | Manualshive

Page: 11 / 24

MultiMax 6DS User Manual Download Page 11

Seite 11 von 24

1.4.3 Powering-on the printer

CAUTION:

Be sure the power switch is turned off before connecting the power cord (the

“0” side of the ON/OFF rocker switch should be pressed).

WARNING KEEP FINGERS AND OTHER BODY PARTS AWAY FROM

THE CUTTING AREA. THERE ARE HAZARDOUS MOVING PARTS.

Plug the female end of the AC power cord into the receptacle located in the power
entry module on the printer’s rear panel.

Plug male end of the AC power cord into a properly grounded wall socket.

Power on the printer by pressing the “I” side of the ON/OFF rocker switch located on
the power entry module on the rear panel.

The LCD display will activate and an initializing process will begin. Depending on
whether there is media loaded or not, the process will be different. When there is no
media loaded, the MultiMax 6ds will prompt the user for a media load procedure. When
media is loaded, the MultiMax 6ds will measure the media width and check the
presence of the cassettes and estimate how much usable ribbon is remaining on the
roll

«
...
9
10
11
12
13
...
»

Summary of Contents for 6DS

























Reviews:

No comments