background image

  

For your safety 

Basic safety instructions 

 

  

  

3030247600-02-EN  

  

 

For your safety 

 

Basic safety instructions 

Please read the following safety instructions carefully before using the product for 
the first time. 
  ▪  Do not make any unauthorized modifications to the product. Unauthorized 

modifications or use may impair safety and reduce the service life or operability 
of the unit. Modifications are considered unauthorized if they are not described 
in the product documentation. 

  ▪  Comply with road traffic rules. Stop the vehicle before operating the GPS 

receiver or connected components. 

 

Intended use 

The product is intended for accurate positioning of agricultural vehicles. 

The product is intended exclusively for use in agriculture. The manufacturer shall not 
be held responsible for any other use of the system. 

The operating instructions form part of the product. The product may only be used in 
accordance with these operating instructions. 

The manufacturer cannot be held liable for any personal injury or property damage 
resulting from such non-compliance. All risk arising from improper use lies with the 
user. 

 

Layout and meaning of warnings 

All safety instructions found in these Operating Instructions are composed in 
accordance with the following pattern: 

  

 

 

WARNING 

This signal word identifies medium-risk hazards, which could potentially cause 
death or serious physical injury, if not avoided. 

 

  

 

 

CAUTION 

This signal word identifies hazards that could potentially cause minor or moderate 
physical injury or damage to property, if not avoided. 

 

1.1 

  

 

1.2 

1.3 

Summary of Contents for 3030247600














Reviews: