Muirhead 3565 Product Manual Download

Page: 22 / 28

22 | 28

M0160.docx | Rev 1.3 | Modified on 19/05/2020 | © Remote Control Technologies Pty Ltd

Pressure Switches to suit Temperature Monitoring Applications

Part No. Description

1764

Temperature Switch 212 °F / 100 °C, N/C, 2 Terminal, 3/8 NPT

1765

Temperature Switch 220 °F / 104 °C, N/C, 2 Terminal, 3/8 NPT

1766

Temperature Switch 230 °F / 110 °C, N/C, 2 Terminal, 3/8 NPT

1767

Temperature Switch 250 °F / 120 °C, N/C, 2 Terminal, 3/8 NPT

1768

Temperature Switch 275 °F / 135 °C, N/C, 2 Terminal, 3/8 NPT

8491

Temperature Switch 225 °F / 107 °C, N/C, 2 Terminal, O-ring, 3/4 UNO

3379

Adaptor Bush 3/8 NPT Female To 1/2 NPT Male, To Suit 3/8 NPT Temperature Switches

Flow Switches to suit Coolant Flow Applications

Part No.

Description

6041

Flow Switch, N/O 56 mm Plug, Suits Engine Numbers 3306, 3406, 3408, 3508, 3512, and 3516

3690

Flow Switch, N/O 69 mm Paddle, Suits Engine Number 3306

Oil/Fuel Level Switches to suit the Oil Level Monitoring Applications.

Part No.

Description

3072

Oil Level Switch Capacitive, N/O , 1/4 NPT, Used For Temperatures Below 100 °C

Alarms to suit the Warning Alert Function of the Control Unit.

Part No.

Description

1723

Warning Alarm, 80 dB Constant or Intermittent Siren 12/24 V

6162

Warning Alarm 102 dB 12/24 V Heavy Duty

9655

Dual-Hole Mounting Bracket To Suit 1723 Warning Alarm

6444

Single-Hole Mounting Bracket To Suit 1723 Warning Alarm

Note

The sensors and switches listed in this manual are only a small selection available from RCT. If a sensor is

required for a specific application, please contact your local RCT branch or distributor; alternatively, email

[email protected].

Summary of Contents for 3565





























Search results

Summary of Contents for 3565

Reviews:

Related manuals for 3565

Brands by name

Popular brands

Muirhead 3565, Product Manual

Search results

Summary of Contents for 3565

Reviews:

Related manuals for 3565

Brands by name

Popular brands